User manual PHILIPS AZ8051/11D

[. . . ] Toutefois, si vous ne parvenez pas à résoudre votre probléme, vous pouvez accéder à notre aide en ligne à l'adresse Necesita ayuda inmediata? Lea primero la Guía de uso rápido o el Manual del usuario, en donde encontrará consejos que le ayudarán a disfrutar plenamente de su producto Philips. Si después de leerlo aún necesita ayuda, consulte nuestro servicio de asistencia en línea en www. philips. com/usasupport or call www. philips. com/usasupport ou formez le www. philips. com/usasupport o llame al teléfono 1-888-PHILIPS (744-5477) while with your product. (and Model / Serial number) 1-800-661-6162 (Francophone) 1-888-PHILIPS (744-5477) (English speaking) Veillez à avoir votre produit à portée de main. (et model / serial nombre) 1-888-PHILIPS (744-5477) y tenga a mano el producto. [. . . ] Helpful hints: · To improve radio reception For FM, extend, incline and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. For AM, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. · · Back/bottom panels (See 1) 9 Telescopic antenna ­ improves FM reception 0 Battery door ­ open to insert 6 x 1. 5V R-14/ UM-2/ C-cells !p ­ 3. 5 mm stereo headphone socket Helpful hints: The speakers will be muted when headphones are connected to the set. @ AC MAINS~ ­ inlet for power cord CD Player Playing a CD · This CD player plays Audio Discs including CD-Recordables (CD-R) and CD-Rewritables (CD-RW). MP3, CD-ROM, CD-I, CDV, VCD, DVD or computer CDs are not possible for playback. CD Player Selecting a different track · Press / § once or repeatedly until the desired track number appears in the display. · In the pause/stop position, press 2; to start playback. 1 Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. In the stop position, press PROG to activate programming. Helpful hints: When your searching reaches the end of the last track, the CD goes to stop mode. 2 3 2 2 3 ­ 4 4 5 6 7 5 ­ When playback of your program comes to the stop position, your set will return to normal playback. To re-enter program mode, press PROG in the stop position. Reviewing the program In the stop position, press PROG repeatedly to see your stored tracks. Erasing a program You can erase the contents of the memory by: ­ in the stop position, press PROG to enter program mode, and then press 9; ­ selecting FM, AM or OFF; ­ opening the CD door. ­ ­ you open the CD door; ­ you select FM, AM or OFF; ­ the CD has reached the end. 2 ­ Maintenance & Safety (See 7) CD player and CD handling · If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. The lens of the CD player should never be touched!Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. Always close the CD-tape door to avoid dust on the lens. To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. [. . . ] Problem ­ Possible cause · Remedy No hay sonido/energía ­ Volume not adjusted · Adjust the VOLUME ­ Power cord not securely connected · Connect the AC power cord properly ­ Batteries dead/ incorrectly inserted · Insert (fresh) batteries correctly ­ Headphones connected to the set · Disconnect headphones. ­ CD contains non-audio files · Press , § once or more to skip to a CD audio track, instead of the data file. If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Do not open the set as there is a risk of electric shock. [. . . ]