User manual PHILIPS BDL3731V

[. . . ] User Manual BDL3731V SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user's authority to operate it. Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. Attention: Pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne correspondante de la prise et pousser jusqu'au fond. Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U. S. Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights. TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] Connect the red (R) and white (L) audio jacks of the device to the R and L audio-in jacks of the monitor. 14 User Manual BDL3731V 4. 1. 4 1 2 USING VIDEO INPUT Connect the jack of the external device to the VIDEO INPUT of the monitor. Connect the red (R) and white (L) audio jacks to the R and L audio-in jacks located next to the VIDEO connector. 4. 1. 5 1 2 USING MONITOR OUTPUT Connect the jack of the DVD or VCR (for recording) or audio system to the MONITOR OUTPUT of the monitor. Connect the red (R) and white (L) audio jacks to the R and L audio-out jacks located next to the VIDEO connector. 4. 1. 6 1 2 USING DVI INPUT Connect the DVI-jack of the DVD, decoder or satellite receiver to the DVI INPUT of the monitor. Connect the red (R) and white (L) audio jacks to the R and L audio-in jacks located next to the DVI connector. 4. 1. 7 1 USING HDMI INPUT Connect the HDMI-jack of the external device to the HDMI INPUT of the monitor. 15 User Manual BDL3731V 4. 2 4. 2. 1 EXTERNAL AUDIO CONNECTION CONNECTING EXTERNAL SPEAKER Connect the speaker audio cable to the external speaker output jack on the rear of the LCD. · Before connecting the speaker wire to the LCD, turn off your LCD. 4. 2. 2 USING DIGITAL AUDIO OUTPUT Connect the optical cable to the DIGITAL AUDIO OUTPUT on the rear of the LCD. 16 User Manual BDL3731V 4. 3 4. 3. 1 CONNECTING A PC USING RGB (VGA) OR DVI VIDEO INPUT 1 1 Connect the 15-pin D-Sub RGB(VGA) connector of the PC to the RGB-IN connector of the monitor. If you have a PC that is equipped with a DVI (Digital Visual Interface), you may connect the PC DVI connector from the PC to the DVI-IN connector of the monitor. For both RGB (VGA) and DVI, connect the red (R) and white (L) audio jacks of the PC to the R and L (DVI/RGB) AUDIO IN jacks of the monitor. 2 Setting Up Your Display Using Plug and Play This display adheres to VESA Plug and Play standard to eliminate complicated and time consuming setup of monitors. This monitor identifies itself to the computer and automatically sends the PC its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols. How to Set up Your PC for Use with Monitor (Windows) The display settings for a typical Windows-based computer are shown below. However, the actual screens on your computer will differ depending on the version of Windows and video card equipped with the computer. Even though the actual screen may look different from example displayed below, basic set-up routine will apply in most cases. 1 Go to the Window's CONTROL PANEL by clicking START, SETTINGS, CONTROL PANEL. => The CONTROL PANEL Window is displayed. Select the DISPLAY icon from this window. => The DISPLAY PROPERTIES dialog box is displayed. Select the SETTINGS tab to display your computer's video output settings. Set the "Screen Resolution" settings to 1024x768 PIXELS. For COLOR QUALITY, select 24 BIT COLOR (might also be expressed as 16 million colors). If a vertical-frequency option is available, set the value to 60 or 60 Hz. Click OK to complete the setting. 2 3 2 3 4 4 5 5 6 Note: Both screen position and size will vary, depending on the type of PC graphics card and its resolution selected. See page 30 for an overview of the supported resolutions. 17 User Manual BDL3731V 5. BASIC FUNCTIONS 5. 1 POWERING ON / OFF Make sure the monitor is plugged into the wall outlet with the supplied power cord. If the power is plugged in, the STATUS LED on the control panel will illuminate in red color. Using Front Panel or Remote Control 1 Press the POWER button on the front panel or remote control. [. . . ] product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics Europe. reception problems caused by signal conditions or cable or antenna systems outside the unit. a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications. incidental or consequential damages resulting from the product. [. . . ]