User manual PHILIPS BDL4221V-27B

[. . . ] Manual file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/MANUAL. HTM2006-03-10 1:33:25 PM Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance · FAQs · Troubleshooting · Regulatory Information · Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your computer monitor: q q q q q q q q q q q q Unplug the monitor if you are not going to use it for an extensive period of time. Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. [. . . ] To change a fuse in this type of plug proceed as follows: 1. Fit new fuse which should be a BS 1362 5A, A. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere. How to connect a plug The wires in the mains lead are coloured in accordance with the following code: BLUE - "NEUTRAL" ("N") BROWN - "LIVE" ("L") GREEN & YELLOW - "EARTH" ("E") 1. The GREEN AND YELLOW wire must be connected to the terminal in the plug which is file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/SAFETY/REGS/REGULAT. HTM (9 of 10)2006-03-10 1:33:59 PM Regulatory Information marked with the letter "E" or by the Earth symbol or coloured GREEN or GREEN AND YELLOW. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. The BROWN wire must be connected to the terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires. RETURN TO TOP OF THE PAGE Waste Electrical and Electronic Equipment-WEEE Attention users in European Union private households This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/SAFETY/REGS/REGULAT. HTM (10 of 10)2006-03-10 1:33:59 PM Other Related Information Other Related Information Safety and Troubleshooting · FAQs · Troubleshooting · Regulatory Information · Information for Users in the U. · Information for Users Outside the U. S Information for Users in the U. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V. For units set at 230 V: Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a tandem blade, grounding type attachment plug rated 15 A, 250 V. Information for Users outside the U. S. For units set at 230 V: Use a Cord Set consisting of a minimum 18 AWG cord and grounding type attachment plug rated 15 A, 250 V. The Cord Set should have the appropriate safety approvals for the country in which the equipment will be installed and / or be marked HAR. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/SAFETY/saf_other. htm2006-03-10 1:33:59 PM Philips Pixel Defect Policy Philips Pixel Defect Policy Product Features · Technical Specifications · Resolution and Preset Modes · Automatic Power Saving · Physical Specification · Pin Assignment · Product Views Philips' LCD Panel Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practise stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels. [. . . ] box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S. A. -Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information Centre Norte 45 No. 669 Col. Industrial Vallejo C. P. 02300, -Mexico, D. F. Phone: (05)-3687788 / 9180050462 Fax : (05)-7284272 PARAGUAY Av. [. . . ]