User manual PHILIPS BDL4671VL

[. . . ] BDL4271VL BDL4671VL www. philips. com/welcome User Manual (English) BDL4271VL / BDL4671VL Safety Instructions Warnings and Precautions KNOW THESE SAFETY SYMBOLS CAUTION:  REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). TO REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. CAUTION: F  CC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it. CAUTION:  prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. To TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] Card OPS audio Select the analog or digital audio mode for card OPS. 4. 2. 3. Audio menu Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Balance Treble Bass Volume Maximum volume Minimum volume Mute Audio source Audio reset Card OPS audio 4. 2. 4. PIP menu Picture Screen Audio PIP Configuration1 Configuration2 Advanced option PIP PIP input PIP change PIP size PIP audio PIP reset Balance Adjust to emphasize left or right audio output balance. Treble Adjust to increase or decrease higher-pitched sounds. Bass Adjust to increase or decrease lower-pitched sounds. Volume Adjust to increase or decrease the audio output level. Maximum volume Adjust your own limitation for the maximum volume setting. This stops the volume from being playing at too loud a level. Minimum volume Adjust your own limitation for the minimum volume setting. PIP Select the PIP (Picture-in-Picture) mode. Choose from: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}. PIP input Select the input signal for the sub-picture. PIP change Enlarges the smaller picture to become the main picture, and vice versa. PIP size Select the size of the sub picture in the PIP (Picture-in-Picture) mode. Choose from: {Small} / {Medium} / {Large}. PIP audio Select the audio source in the PIP (Picture-in-Picture) mode. • {Main} - Select audio from the main picture • {Sub} - Select audio from the sub picture. PIP reset Reset all settings in the PIP menu to factory preset values. NOTES: 19 BDL4271VL / BDL4671VL • The PIP function is available only for the following condition: {Configuration1} - {Panel saving} - {Pixel shift} setting to [Off] and {Advanced option} - {Tiling} - {Enable} setting to [No]. • The PIP function is available only for certain signal source combinations as shown in the table below. • The availability of the PIP function will also depend on the resolution of the input signal being used. Main Picture Sub Picture Displayport HDMI DVI-D VGA YPbPr Video USB Card OPS Displayport X X X O O O X X HDMI X X X O O O X X DVI-D X X X O O O X X VGA O O O X X X O O YPbPr O O O X X X O O Video O O O X X X O O USB X X X O O O X X Card OPS X X X O O O X X Auto adjust Use this function to automatically optimize the display of VGA input image. NOTE:  This item is functional for VGA input only. Power save Use this setting to reduce the power automatically. • {RGB} - Select {On} to let the display enter APM mode when no signal is detected from the HDMI Graphic mode, HDMI, DVI-D, or VGA inputs after three successive cycles. [. . . ] 3. The selected input has no connection. 2. Make sure the power switch is switched on. 3. Connect a signal connection to the display. Symptom No picture is displayed Interference displayed on the display or audible noise is heard Color is abnormal Picture is distorted with abnormal patterns Caused by surrounding electrical appliances or fluorescent lights. The signal cable is not connected properly. [. . . ]