User manual PHILIPS BTM 2056

[. . . ] If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 3 Amp. Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. [. . . ] Insert a disc with the printed side facing up and press down on OPEN/CLOSE0 to close the CD door. READING is displayed as the CD player scans the contents of a disc, and then the total number of tracks and playing time (or the total number of albums and tracks for MP3 disc) are shown. Playing an MP3/WMA disc 1 Load an MP3/WMA disc. The disc reading time may exceed 10 seconds due to the large number of songs compiled into one disc. AXX is the total album number and TXX is the total track number. Press TUNING à / á (or ALBUM/ PRESET +/- on the remote control) to select a desired album. Press í/ ë to select a desired track. Press 2; to star t playback. 3 2 3 4 Basic playback controls To play a disc Press 2; to start playback. The current track number and elapsed playing time of the track are displayed during disc playback. During playback, press DISPLAY/CLOCK to show the album name and ID3 information. 15 English CD/MP3 Operation Supported MP3 disc formats: ­ ISO9660, Joliet, UDF 1. 5 ­ Maximum title number: 999 (depending on filename length) ­ Maximum album number: 99 ­ Supported sampling frequencies: 32 kHz, 44. 1 kHz, 48 kHz ­ Supported Bit-rates: 32~256 (kbps), variable bitrates 3 English To return to normal playback, press SHUFFLE or REPEAT until the various SHUFFLE/ REPEAT modes are no longer displayed. You can also press 9 to cancel your play mode. Note: ­ The SHUFFLE and REPEAT functions cannot be used simultaneously. Information display during playback In CD mode Press DISPLAY/CLOCK repeatedly to see the following information. Track number and elapsed playback time of current track. Track number and remaining playback time of current track. Press PROG on the remote control to activate programming. Press í/ ë (or ALBUM/PRESET +/- on the remote control) to allocate a number from 1 to 40 to this station. Press PROG on the remote control again to confirm the setting. Repeat the above four steps to store other stations. 3 4 5 3 You can override a preset station by storing another frequency in its place. To tune to a weak station, press TUNING à / á (or à / á on the remote control) briefly and repeatedly until you have found optimal reception. Tuning to preset radio stations Press í/ ë (or ALBUM/PRESET +/- on the remote control) until the desired preset station is displayed. Programming radio stations You can store up to a total of 40 radio stations in the memory. Automatic programming Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden. The system will only programme stations which are not in the memory already. RDS Radio Data System is a service that allows FM stations to show additional information. If and the you are receiving a RDS station, station name are displayed. When automatic programming is used, RDS stations will be programmed first. Scrolling through different RDS information Press RDS on the remote control briefly and repeatedly to scroll through the following information (if available): ­ Station name ­ Radio text messages ­ Program type ­ Frequency 1 Press í/ ë (or ALBUM/PRESET +/- on the remote control) to select the preset number where programming should start. Note: ­ If no preset number is selected, default is preset (1) and all your presets will be overridden. 17 English USB Connection English Using USB connectivity BTM 2056 is fitted with a USB port in the front panel, offering a plug and play feature which allows you to play, from your BTM 2056, digital music and spoken contents stored on a USB mass storage device. [. . . ] Increase the distance between the Mini HiFi System and your TV or VCR. The system does not react when buttons are pressed. Remove and reconnect the AC power plug and switch on the system again. Sound cannot be heard or is of poor quality. Adjust the volume. Check that the speakers are connec ted correctly. Check if the stripped speaker wire is clamped. Make sure the MP3-CD was recorded within 32-256 kbps bit rate with sampling frequencies at 48 kHz, 44. 1 kHz or 32 kHz. The left and right sound outputs are reversed. Check the speaker connections and location. Troubleshooting Problem The remote control does not function properly. Solution Select the source (CD or FM, for example) before pressing the function button (É, í, ë). Reduce the distance between the remote control and the system. Insert the batteries with their polarities (+/­ signs) aligned as indicated. Replace the batteries. [. . . ]