User manual PHILIPS BTM2180

[. . . ] Always there to help you Register your product and get support at www. philips. com/welcome BTM2180 Question?Contact Philips User manual Contents 1 Important 3 7 Product information Safety 3 Specifications USB playability information Supported MP3 disc formats 15 2 Your micro system Introduction 5 What's in the box 5 Overview of the main unit 6 Overview of the remote control 7 5 15 16 16 8 Troubleshooting 9 Notice 17 19 3 Get started Connect speakers Connect power Demonstrate the features Prepare the remote control Set clock Turn on 8 8 8 8 9 9 9 4 Play Play from disc Play from USB Control play Skip to a track Program tracks Play from Bluetooth-enabled devices 10 10 10 10 11 11 11 5 Listen to the radio Tune to a radio station Program radio stations automatically Program radio stations manually Select a preset radio station 13 13 13 13 13 6 Other features Set the alarm timer Set the sleep timer Listen to an external device 14 14 14 14 EN 2 1 Important Safety h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. i Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] »» Play starts automatically. If not, press . Play from USB Note •• Make sure that the USB device contains playable audio content. 1 2 Press USB/AUDIO IN repeatedly to select the USB source. »» Play starts automatically. If not, press . FM CD PRESET/ALBUM AUDIO IN USB SOURCE VOLUME REPEAT VOL CD SHUFFLE FM CD PRESET/ALBUM AUDIO IN MUTE DISPLAY PROG TIMER AUDIO IN SOURCE VOLUME SOUND CLOCK SLEEP REPEAT VOL SHUFFLE AUDIO IN MUTE DISPLAY PROG TIMER SOUND CLOCK SLEEP Control play / / Select a folder. Enrich sound effect with DSC: balanced, clear, powerful, warm, and bright. Adjust display brightness. REPEAT SHUFFLE VOL +/MUTE SOUND DISPLAY EN 10 Skip to a track For CD: Press / to select another track. For MP3 disc and USB: Play from Bluetooth-enabled devices Note •• The effective operation range between the unit and your Bluetooth enabled device is approximately 10 meters (30 feet). •• Any obstacle between the system and the device can reduce the operational range. •• Compatibility with all Bluetooth devices is not guaranteed. 1 2 Press Press / / to select an album or a folder. to select a track or a file. Program tracks You can program a maximum of 20 tracks. 1 2 3 4 5 Press PROG to activate the program mode. / to select an SOURCE VOLUME Press / to select a track, and then press PROG to confirm. Repeat steps 2-3 to program more tracks. »» During play, [PROG] (program) is displayed. To tune to a weak station: Press / repeatedly until you find optimal reception. Select a preset radio station In tuner mode, press number. / to select a preset Program radio stations automatically Note •• You can program a maximum of 20 preset radio stations (FM). In tuner mode, press and hold PROG for more than two seconds to activate automatic programming. »» All available stations are programmed in the order of waveband reception strength. »» The first programmed radio station is broadcast automatically. 13 EN 6 Other features Set the alarm timer This unit can be used as an alarm clock. You can select CD, FM, or USB as alarm source. Note •• Make sure that you have set the clock correctly. Set the sleep timer To set the sleep timer, in turn on mode, press SLEEP/TIMER repeatedly to select a set period of time (in minutes). »» When sleep timer is activated, is displayed. Otherwise, disappears. Listen to an external device You can listen to an external device through this unit with an MP3 link cable. 1 2 3 4 In standby mode, press and hold SLEEP/ TIMER for more than two seconds. »» The hour digits are displayed and begin to blink. »» The minute digits are displayed and begin to blink. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Relocate the receiving antenna. • Increase the separation between equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]