User manual PHILIPS CD RADIO CASSETTE RECORDER AZ1013

[. . . ] 3 To switch off the set, adjust the source selector to TAPE/OFF position and check the cassette keys are released. 2 Connect the power cord to the AC MAINS inlet and the wall outlet. The power supply is now connected and ready for use. 3 To switch off completely, unplug the power cord from the wall outlet. · Unplug the power cord from the wall outlet to protect your set during heavy thunderstorms. The type plate is located on the bottom of the set. RE T PEA 9 English P M T Radio English 10 CD-Player Playing a CD AZ1008RECORDER TTE IO CASSE RDING START RECO LI F T Radio reception AZ1008RECORDER TTE IO CASSE TO CD RAD CD LI F T TUNING LIFT T O O PE N OPE N TUNING LIFT T O O PE N CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY CD MW FM TAP F OF VOL UM E SEAR CH PAUS SEAR CH PLAY TO CD RAD RECO RDING O START SYNCHR CD SY OPE N NCHRO E STOP · OPEN VOL UM E E BAT T. LOW CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT P STOP · OPEN T. LOW PROGRA M PROGRA RE T PEA SEARCH DY SEARCH DY AMI N BOO S C BASS AMI N C BASS BOO S DBB DBB 1 Adjust the source selector to AM or FM to select your desired waveband. [. . . ] 2 To return to normal playback press REPEAT until the REPEAT modes are no longer shown. · You can also press STOP 9 to quit the play mode. RE T PEA 11 English P M T P M T CD-Player English 12 Programming track numbers You may store up to 19 tracks in the desired sequence. If you like, store any track more than once. CD RAD Cassette Recorder Erasing a program You can erase the contents of the memory by: ­ opening the CD door; ­ selecting AM, FM or TAPE sound source; ­ pressing STOP 9 (twice during playback or once in the stop position. ) Display: PROGRAM disappears. AZ1008RECORDER TTE IO CASSE RDING START RECO LI F T TUNING LIFT T O O PE N CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY TO CD SY OPE N NCHRO E STOP · OPEN VOL UM E CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT P T. LOW PROGRA M RE T PEA SEARCH DY AMI N C BASS BOO S DBB CASSETTE RECORDER Cassette playback 1 Adjust the source selector to TAPE/OFF. 1 In the STOP mode, press PROGRAM to activate program mode. 2 Press SEARCH or § for your desired track. Your selected track number and PROGRAM flashes. LI F T TUNING LIFT T O O PE N 3 Press PROGRAM to store the track. 00 and PROGRAM flashes, ready for your next track selection. 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. -- and PROGRAM flashes in the display if you attempt to program more than 19 tracks. 5 To play your program, press PLAY·PAUSE 2;. Reviewing your program · In the stop position, press PROGRAM repeatedly to see your stored track numbers. CD MW FM TAP F OF SEAR CH PAUS SEAR CH PLAY TO OPE N CK CD TRA Y/ PAUSE PLA ST O REPEAT PROGRAM BAT SEARCH DY AMI N C BASS BOO S DBB 3 Close the cassette door. 5 To pause playback press PAUSE ;. To resume, press the key again. 6 By pressing SEARCH 5 or 6, fast winding of the tape is possible in both directions. To stop fast winding, press STOP·OPEN 9/. 7 To stop the tape, press STOP·OPEN 9/. · The keys are automatically released at the end of the tape, and the set is switched off, except if PAUSE ; has been activated. RE T 2 Press STOP·OPEN 9/ to open the cassette door and insert a recorded cassette. CD RAD AZ1008RECORDER TTE IO CASSE RDING START RECO CD SY NCHRO E STOP · OPEN VOL UM E T. LOW P PROGRA M T PEA T Recording General information on recording · Recording is permissible insofar as copyright or other rights of third parties are not infringed. · This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not been broken. · The best recording level is set automatically. Altering the VOLUME and DBB controls will not affect the recording in progress. · At the very beginning and end of the tape, no recording will take place during the 7 seconds when the leader tape passes the recorder heads. · To protect a tape from accidental erasure, have the tape in front of you and break out the left tab. Recording on this side is no longer possible. To record over this side again, cover the tabs with a piece of adhesive tape. Synchro Start CD recording 1 Select CD source. CD RAD · Playing of the CD program starts automatically from the beginning of the program. [. . . ] Do not open the set as there is a risk of electric shock. If you are unable to remedy a problem by following these hints, consult your dealer or service center. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. Problem No sound Power cord not securely connected Batteries dead /incorrectly inserted Display does not function properly/ No reaction to operation of any of the controls Er indication CD badly scratched or dirty Laser lens steamed up CD-(R) is blank or the disc is not finalized CD playback does not work The CD skips tracks Poor cassette sound quality Solution ­ Adjust the VOLUME ­ Connect AC power cord properly ­ Insert (fresh) batteries correctly ­ Electrostatic discharge ­ Switch off and unplug the set. ­ No CD inserted, insert a CD ­ Replace/ clean CD, see Maintenance ­ Wait until lens has cleared ­ Wait until lens has acclimatized ­ Use a finalized CD-(R) ­ CD badly scratched/ dirty. [. . . ]