User manual PHILIPS CD RADIO CASSETTE RECORDER AZ1050

[. . . ] review mode ¡ EASY JOG TM . . . . . . . . - previous/next track (Play and (rotate) Program mode) - recording level control (recording) - selects settings (menu on) ENTER (push) . . . . . . . . . . . . . . - plays selected tracks - selects settings in Menu mode - programs track numbers ¡ STORE/MENU . . . . . . . . . . . . - enters Menu mode - stores Menu settings TM CANCEL/DELETE . . . . . . - deletes tracks from a program - deletes text in Menu mode - returns to a higher level in the menu £ PHONES . . . . . . . . . . . . . . . . . . . . . . socket for headphones IR sensor . . . . . . . . . . . . . . . . . . . . receives signals from the remote control Note: Unless stated otherwise, all controls are on the front of the CD recorder. When provided on the remote control, you can also use the corresponding buttons, after selecting the CD recorder or separate CD player by pressing CDR or CD. Connections at the back 1 Connection to mains 2 ANALOG IN . . . . . . . . . . . . . . . . connects to the line output of an amplifier (left and right) 3 ANALOG OUT CDR . . . . connects to the line input of an amplifier (left and right) 4 DIGITAL IN. . . . . . . . . . . . . . . . . . connects to the digital coaxial output of an external CD player 5 DIGITAL OUT CDR . . . . connects to the digital coaxial input of e. g. amplifier or recording device 6 OPTICAL IN . . . . . . . . . . . . . . . . connects to the digital optical output of an external CD player INSTALLATION English Connections general For recording the following inputs are present: - Digital optical input. [. . . ] amplifier or recording device 6 OPTICAL IN . . . . . . . . . . . . . . . . connects to the digital optical output of an external CD player INSTALLATION English Connections general For recording the following inputs are present: - Digital optical input. For playback the following outputs are present: - Digital coaxial output. We advise you to connect these to the CD input on your amplifier. The connections you make will depend upon the possibilities your audio equipment offers. Please refer to the user manuals for your other audio equipment first. Analog connections Analog connection is required for playback of CDs (use cable 2) and for recording from external analog sources (use cable 1). L L R IN R OUT RECEIV 2 TAPE ER 1 L L R IN ANAL Digital recordings (optical or coaxial) give the best performance in audio and usability (e. g. auto-track). (The digital optical connection is less sensitive to external disturbances). If your equipment does not offer digital connections, the high quality Analog-Digital-Convertor of your CD recorder will ensure very good audio performance when recordings are made from the analog input. 2 For recording, connect a fibre-optic cable 4 between the digital optical input of the CD recorder and the digitaloptical output of a CD player. Note: For playback, the digital coaxial output or analog output should be connected to an amplifier. 12 INSTALLATION English 13 Power supply Inserting batteries in the remote control 1 Plug the power cord supplied into the MAINS connector on the CD recorder, then into a mains socket. §The CD recorder will switch on. 1 Open the battery compartment cover. 2 Insert 2 batteries ("AA", LR-6 or UM-3; as supplied) as shown. 3 Replace the cover. Note: - If the CD recorder is in Standby mode (red led on), press any key to activate the recorder. - The CD recorder will automatically adjust to the local mains voltage. - When the CD recorder is in the `OFF' position, it is still consuming some power. If you wish to disconnect your player completely from the mains, withdraw the plug from the AC outlet. Note: We recommend you use 2 batteries of the same type and condition. [. . . ] - When the CD recorder is in the `OFF' position, it is still consuming some power. If you wish to disconnect your player completely from the mains, withdraw the plug from the AC outlet. Note: We recommend you use 2 batteries of the same type and condition. Batteries contain chemical substances, so they should be disposed of properly. Setup recommendations - Place the CD recorder on a solid, vibration free surface. [. . . ]