User manual PHILIPS CD RCR 1 DECK 1 PIECE AZ100017

[. . . ] Follow Instructions - All operating and use instructions should be followed. Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer. An appliance and cart combination should be moved with care. [. . . ] · To interrupt recording, press PAUSE on the CD recorder. To resume, press RECORD on the CD recorder. After recording the display will show UPDATE for several seconds. This feature enables you to make fast and easy recordings of a CD. Track increments are automatically detected from the source material. Track increments cannot be added manually. In analog source material a silence of 2. 7 seconds or more is automatically detected as a track increment. Important: - Recording from CD-changers should always be started in the RECORD DISC, RECORD TRACK or MAKE CD mode. Preparing for autostart recording 1 Make sure the disc is absolutely free of scratches and dust particles. 2 Press Source repeatedly until (depending on the connection used): § DIGITAL I d, DIGITAL I I d, OPTICAL I p or ANALOG a lights up and DIGITAL 1, DIGITAL 2, OPTICAL or ANALOG will appear on the display. REM REC TIME TRACK TOTAL REM TRACK TIME FADE STEP Note: Recordings from DAT, DCC or analog sources will only stop after 20 seconds of silence. Important: If you want to play the recorded CDR disc on a regular CD player, it must be finalized. Finalized CDRW discs play only on CDRW compatible CD players. DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL 3 With the CD recorder stopped, press REC TYPE once: to select 'RECORD DISC'; twice: to select 'RECORD TRACK'; four times: to select `MAKE CD'. § d and SYNC start to flash and the display shows the selection. REM REC TIME TRACK TOTAL REM TRACK TIME FADE STEP DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL · If CHECK INPUT message also flashes, the digital connection is incorrect. 18 RECORDING English 19 Manual recording 3 With the recorder stopped, press REC TYPE three times to enter the Manual Record standby mode. § MANUAL starts to flash and the display shows REC MANUAL. REM RECORD REC TIME TRACK TOTAL REM TRACK TIME FADE STEP DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL Important: - Recording from CD-changers should always be started in the RECORD DISC, RECORD TRACK or MAKE CD mode. - Only make analog recordings when digital recording is not possible. Preparing for manual recording 1 Make sure the disc is absolutely free of scratches and dust particles. 2 Use the REC TYPE key to select the required recording mode: RECORD DISC, RECORD TRACK, REC MANUAL or MAKE CD. 3 To start recording press PLAY on the selected source (RECORD DISC, RECORD TRACK or MAKE CD selected). · Press RECORD on the recorder and PLAY on the selected source (REC MANUAL selected). · Use the LEVEL (Mic) key to mix your voice with the sound from the source. · Use the EASY JOG key to set the recording level. · For details about recording see the instructions in the previous sections. Microphone recording 1 Connect a (stereo) microphone to the MIC socket. The source active previously will be selected automatically. 2 Press Source repeatedly until MICROPHONE is displayed. REM REC TIME TRACK TOTAL REM TRACK TIME FADE STEP Sample rate convertor (Monitor mode) The sample rate convertor is used to convert input signals into CD-standard digital output signals. 1 Connect the non-digital source to one of the input sockets of the recorder. 2 Connect the optional recording device to the DIGITAL OUT or OPTIONAL OUT output socket. [. . . ] § ON or OFF will appear on the display for 2 seconds. 5 Rotate EASY JOG/ENTER to select SET FADE IN or SET FADE OUT. 6 Press EASY JOG/ENTER or enter on the remote control to confirm. § 2000 MS will appear on the display. [. . . ]