User manual PHILIPS CD RECORDER CDR570BK99

[. . . ] review mode ) OPEN/CLOSE /. . . . . . . . . . opens/closes disc tray ¡ RECORD . . . . . . . . . . . . . . . . . . . . . . starts recording, finalising, erasing TM REC(ord) TYPE . . . . . . . . . . . . selects recording modes £ LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . headphone volume control PHONES . . . . . . . . . . . . . . . . . . . . . . socket for headphones LEVEL (MIC). . . . . . . . . . . . . . . . microphone/mix level controller § MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . socket for (stereo) microphone Note: Unless stated otherwise, all controls are on the front of the CD recorder. When provided on the remote control, you can also use the corresponding buttons, after selecting the CD recorder or separate CD player by pressing CDR or CD. Connections at the back 1 ANALOG IN . . . . . . . . . . . . . . . . connects to the line output of an amplifier (left and right) 2 ANALOG OUT . . . . . . . . . . . . connects to the line input of an amplifier (left and right) 3 DIGITAL IN 1 . . . . . . . . . . . . . . connects to the digital coaxial output of an external CD player 4 DIGITAL OUT . . . . . . . . . . . . . . connects to the digital coaxial input of e. g. amplifier or recording device 5 DIGITAL IN 2 . . . . . . . . . . . . . . connects to the digital coaxial output of an extra CD player 6 OPTICAL IN . . . . . . . . . . . . . . . . connects to the digital optical output of an external CD player 7 OPTICAL OUT . . . . . . . . . . . . connects to the digital optical input of e. g. [. . . ] amplifier or recording device 5 DIGITAL IN 2 . . . . . . . . . . . . . . connects to the digital coaxial output of an extra CD player 6 OPTICAL IN . . . . . . . . . . . . . . . . connects to the digital optical output of an external CD player 7 OPTICAL OUT . . . . . . . . . . . . connects to the digital optical input of e. g. amplifier or recording device 8 Connection to mains ^ & * 8 INSTALLATION English Connections general For recording the following inputs are present: - Digital optical input. For playback the following outputs are present: - Digital coaxial output. We advise you to connect these to the CD input on your amplifier. The connections you make will depend upon the possibilities your audio equipment offers. Please refer to the user manuals for your other audio equipment first. Digital recordings (optical or coaxial) give the best performance in audio and usability (e. g. (The digital optical connection is less sensitive to external disturbances). This output can be used for digital playback. Note: Your CD recorder is equipped with a digital OPTICAL output. This output can be used for digital playback. 12 INSTALLATION English 13 Power supply Inserting batteries in the remote control 1 Plug the power cord supplied into the MAINS connector on the CD recorder, then into a mains socket. § The recorder is now in Standby mode. 3 Press any key to activate the recorder. 1 Open the battery compartment cover. 2 Insert 2 batteries ("AA", LR-6 or UM-3; as supplied) as shown. 3 Replace the cover. Note: - The CD recorder will automatically adjust to the local mains voltage. - When the CD recorder is in the Standby mode, it is still consuming some power. If you wish to disconnect your recorder completely from the mains, press ON/OFF on the recorder front. Note: We recommend you use 2 batteries of the same type and condition. [. . . ] - When the CD recorder is in the Standby mode, it is still consuming some power. If you wish to disconnect your recorder completely from the mains, press ON/OFF on the recorder front. Note: We recommend you use 2 batteries of the same type and condition. Batteries contain chemical substances, so they should be disposed of properly. Setup recommendations - Place the CD recorder on a solid, vibration free surface. [. . . ]