User manual PHILIPS CD2950B

[. . . ] Register your product and get support at www. philips. com/welcome CD2950 User manual 1 Important safety instructions 2 Your phone 2 3 3 4 5 6 6 6 7 7 8 8 8 8 9 9 9 9 10 10 10 10 10 10 10 11 11 11 11 13 13 13 7 Phone settings What is in the box Overview of the phone Display icons Sound settings ECO mode Name the handset Set the date and time Set the display language 14 14 15 15 15 15 16 16 16 17 17 17 17 17 18 18 18 19 19 20 21 21 21 21 21 23 24 24 25 3 Get started 8 Alarm clock Connect the charger Install the handset Configure your phone (country dependent) Charge the handset Check the battery level What is standby mode?Check the signal strength Switch the handset on or off Set the alarm Turn off the alarm 9 Services 4 Calls Make a call End a call Answer a call Adjust the earpiece/speaker volume Mute the microphone Turn the speaker on or off Make a second call Answer a second call Switch between two calls Make a conference call with the external callers Call list type Auto conference Network type Auto prefix Select the recall duration Dial mode Register the handsets Unregister the handsets Restore default settings 10 Technical data 11 Notice Declaration of conformity Use GAP standard compliance Compliance with EMF Disposal of your old product and batteries 5 Intercom and conference calls Make a call to another handset Transfer a call Make a conference call 12 Frequently asked questions 13 Appendix 14 Index Text and number input tables 6 Text and numbers Enter text and numbers Switch between uppercase and lowercase EN 1 Eng l i sh Contents 1 Important safety instructions Power requirements This product requires an electrical supply of 100-240 volts AC. In case of power failure, the communication can be lost. The voltage on the network is classified as TNV-3 (Telecommunication Network Voltages), as defined in the standard EN 60950. Warning The Electrical network is classified as hazardous. [. . . ] You are now in a 3-way conference call with an external call and a selected handset. Press Note to end the conference call. Press to join an ongoing conference with another handset if [Services] > [Conference] is set to [Auto]. During the conference call Press [Int. ] to put the external call on hold and go back to the internal call. Press [Conf] to establish the conference call again. Note If a handset hangs up during the conference call, the other handset remains connected to the external call. 12 EN 6 Text and numbers You can enter text and numbers for handset name, phonebook records, and other menu items. Enter text and numbers 1 2 3 Press once or several times on the alphanumeric key to enter the selected character. Press Tip For further information on the text and number input, see the chapter 'Appendix'. to add a space. Switch between uppercase and lowercase By default, the first letter of each word in a sentence is uppercase and the rest is lowercase. Press and hold to switch between the uppercase and lowercase letters. EN 13 Eng l i sh 7 Phone settings You can customize the settings to make it your own phone. Make sure that all the handsets registered to the base station are Philips CD29 models in order to have this feature functioning properly. Silent mode You can set your phone to silent mode and enable the silent mode for a specified duration. When the silent mode is turned on, your phone does not ring or send any alerts or sound. Note When you press to find your handset, or when you activate the alarm, your phone still sends alert even when the silent mode is activated. Sound settings Set the handset's ringtone volume You can select among 5 ringtone volume levels or [Off]. 1 2 3 4 Select [Menu] > [Phone setup] > [Silent mode], then press [OK] to confirm. Select [On/off], then press [OK] to confirm. Select [Start & end], then press [OK] to confirm. Set the time, then press [OK] to confirm. is displayed. 1 2 Select [Menu] > [Phone setup] > [Sounds] > [Ring volume], then press [OK] to confirm. Select a volume level, then press [OK] to confirm. The setting is saved. Set the handset's ringtone You can select from 10 ringtones. Set the key tone Key tone is the sound made when you press a key on the handset. 1 2 Select [Menu] > [Phone setup] > [Sounds] > [Ring tones], then press [OK] to confirm. Select a ringtone, then press [OK] to confirm. The setting is saved. 1 2 Select [Menu] > [Phone setup] > [Sounds] > [Key tone], then press [OK] to confirm. Select [On]/[Off], then press [OK] to confirm. The setting is saved. Set the docking tone Docking tone is the sound made when you place the handset on the base station or charger. 1 2 Select [Menu] > [Phone setup] > [Sounds] > [Docking tone], then press [OK] to confirm. Select [On]/[Off], then press [OK] to confirm. The setting is saved. 14 EN You can set the sound in the earpiece among 3 different profiles. 1 2 1 Select [Menu] > [Phone setup] > [Sounds] > [My sound], then press [OK] to confirm. Select a profile, then press [OK] to confirm. Press [Sound] for once or several times to change the sound profile during a call. The name of the handset can be up to 14 characters. It is displayed on the handset screen in standby mode. 1 2 3 Select [Menu] > [Phone setup] > [Phone name], then press [OK] to confirm. [. . . ] Make sure the batteries are inserted correctly. Make sure the handset is placed properly on the charger. The battery icon animates when charging. Make sure the docking tone setting is turned on. [. . . ]