User manual PHILIPS CDC250

[. . . ] If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. [. . . ] The LOAD changer will start CD detection again. Normal Playback (PLAY 2) ­ The display shows the number of the current CD. 3 2 1 · Press PLAY 2 to start playback. ­ The CD number indicator (1-5) always shows what CD is being played (B X flashes). ­ The track being played and its elapsed playing time are shown under TRACK and TRACK TIME. See 'CALLING UP INFORMATION ON THE DISPLAY' if you wish to see other information on the display. TRACK TRACK TIME 1 NOTE!­ You can also press PLAY 2 immediately after inserting the CDs; the compartment then closes automatically and play starts from the first available CD. ­ You can interrupt playback by pressing PAUSE ;; PAUSE then lights up. ­ If you press PLAY 2 during play, the current track will start again from the beginning. ­ You can stop playback by pressing STOP 9 . ­ If you press OPEN/CLOSE during play, the CD compartment will open while play continues. The three CDs outside the changer may now be changed without playback being interrupted. ­ Play will stop after all CDs have been played. · Press POWER-ON/OFF to switch the changer off. 9 CDC775/22-Eng 6/15/00 1:37 PM Page 10 PLAYBACK Selecting Another Track During Play (S T) · Press T or S (less than 0. 5 seconds) until the desired track number appears under TRACK. TRACK TRACK TIME If you reach the end of the last track and release T, play will resume a few seconds before the end of the CD. Scanning CDs (SCAN) All CDs: · Press SCAN before or during play. ­ SELECt dISC lights up and PEAK starts flashing. · Press PEAK SEARCH again to select the last selected disc or press any CD DIRECT PLAY button or DISC (on the remote control) to select the desired disc. ­ The CD will now be scanned for the loudest passage (the peak). ­ The display shows the track being scanned and its elapse playing time. TRACK PEAK TRACK TIME Adjusting The Sound Level (- VOLUME +) (on the remote control only) The volume output of the CD changer can be adjusted. This will affects the analog out, digital out and heaphones level. · Press VOLUME - or + to reduce or increase the sound level. ­ The display will show a value between VOL 0 and VOL 20. Note: ­ Should there be no sound after adjusting the LEVEL control to maximum; press VOLUME + on the remote control to increase the sound level. 1 Important!The volume level will influenced the sound level during recording. Set the volume level to the maximum and do not change the volume setting during recording. CDC775/22-Eng 6/15/00 1:37 PM Page 13 PLAYBACK Activating The Fade-In And Fade-Out Function (FADER) NOTE!­ The FADER function can be used if the changer is connected to the amplifier or the system via the ANALOG OUT output. · During play press FADER. ­ The sound level will now gradually decrease (FADE OUT), after which the changer will go into the PAUSE mode. PROGRAMMING ­ By programming the changer you can play up to 40 tracks in any required sequence. [. . . ] . see the type plate on the rear of the changer Power consumption: . . metal and polystyrene with decorative trim Dimensions (w x h x d): . . 7. 4 kg English 16 TROUBLESHOOTING If a fault occurs, run through the points listed below before taking your changer for repair. If the fault remains, try to clear it by switching the changer off and on again. [. . . ]