User manual PHILIPS CDC486

[. . . ] In an audio rack · The changer can be sited in any desired position. Stacked · Site the changer preferably at the bottom or at the top. · Never position the changer directly on top of a highpower amplifier, as such an amplifier gives off a substantial amount of heat. RECEIVER English 9 Siting the Compact Disc Changer Power Supply Setting · Check that the type plate on the rear of your changer indicates the correct supply voltage. [. . . ] · Press POWER-ON/OFF to switch the changer off. pg 09-21/CDC486/17-Eng 2/16/00 9:26 AM Page 15 PLAYBACK Selecting Another Track During Play (S T) · Press T or S (less than 0. 5 seconds) until the desired track number appears under TRACK. TRACK TRACK TIME If you reach the end of the last track and release T, play will resume a few seconds before the end of the CD. 5 Starting With A Particular CD (CD DIRECT PLAY) · Key in the required CD number. ­ If the CD compartment was open, it will now close. NO dISC lights up when there is no CD in the selected CD compartment. You can also select the number by using the DISC button on the remote control. ­ The music stops and a moment later the selected track begins to play. WRONG tRACK lights up when you select a nonexistent track number. All CDs: · Press SCAN before or during play. ­ If the CD compartment was open, it will now close. ­ SCAN lights up and the first 10 seconds of each track are played in turn (starting from the current track). 10 seconds are counted down each time under REM(aining) TRACK TIME. TRACK REM TRACK TIME 5 Selecting Another CD During Play (CD DIRECT PLAY) · Key in the desired CD number. ­ The music stops and a moment later the selected CD begins to play. NO dISC lights up when there is no CD in the selected CD compartment. You can also select the number by using the DISC button on the remote control. · When the player reaches a track which you wish to hear in full, press SCAN again or PLAY 2. Starting With A Particular Track (CD DIRECT PLAY, S T and PLAY 2) · First select the number of the required CD using CD DIRECT PLAY or DISC on the remote control. ­ The display shows the track being scanned and its elapse playing time. TRACK PEAK TRACK TIME Adjusting The Sound Level (- VOLUME +) (on the remote control only) The volume output of the CD changer can be adjusted. This will affects the analog out, digital out and heaphones level. · Press VOLUME - or + to reduce or increase the sound level. ­ The display will show a value between VOL 0 and VOL 20. Note: ­ Should there be no sound after adjusting the LEVEL control to maximum; press VOLUME + on the remote control to increase the sound level. 1 Important!The volume level will influenced the sound level during recording. Set the volume level to the maximum and do not change the volume setting during recording. 17 English pg 09-21/CDC486/17-Eng 2/16/00 9:26 AM Page 18 PLAYBACK Activating The Fade-In And Fade-Out Function (FADER) NOTE!­ The FADER function can be used if the changer is connected to the amplifier or the system via the ANALOG OUT output. · During play press FADER. ­ The sound level will now gradually decrease (FADE OUT), after which the changer will go into the PAUSE mode. English 18 PROGRAMMING Storing A Program (PROGRAM) ­ By programming the changer you can play up to 40 tracks in any required sequence. ­ FULL lights up if you exceed the maximum of 40 tracks. ­ NO dISC lights up when there is no CD in the selected CD compartment. [. . . ] IEC 958 Power supply Mains voltage and frequency: . . see the type plate on the rear of the changer Power consumption: . . metal and polystyrene with decorative trim Dimensions (w x h x d): . . 7. 4 kg TROUBLESHOOTING If a fault occurs, run through the points listed below before taking your changer for repair. [. . . ]