User manual PHILIPS CDR950

[. . . ] Audio CD Recorder CDR950 · Instructions for use · Mode d'emploi · Instrucciones de manejo · Bedienungsanleitung IMPORTANT SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. [. . . ] Finalized CDRW discs play only on CDRW compatible CD players. DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL 3 With the CD recorder stopped, press REC TYPE once: to select 'RECORD DISC'; twice: to select 'RECORD TRACK'; four times: to select `MAKE CD'. § d and SYNC start to flash and the display shows the selection. REM REC TIME TRACK TOTAL REM TRACK TIME FADE STEP DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL · If CHECK INPUT message also flashes, the digital connection is incorrect. 18 RECORDING English 19 Manual recording 3 With the recorder stopped, press REC TYPE three times to enter the Manual Record standby mode. § MANUAL starts to flash and the display shows REC MANUAL. REM RECORD REC TIME TRACK TOTAL REM TRACK TIME FADE STEP DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL Important: - Recording from CD-changers should always be started in the RECORD DISC, RECORD TRACK or MAKE CD mode. - Only make analog recordings when digital recording is not possible. Preparing for manual recording 1 Make sure the disc is absolutely free of scratches and dust particles. 2 Press SOURCE repeatedly until (depending on the connection used): § DIGITAL I d, DIGITAL I I d, OPTICAL I p or ANALOG a lights up and DIGITAL 1, DIGITAL 2, OPTICAL or ANALOG will appear on the display. REM REC TIME TRACK TOTAL REM TRACK TIME FADE STEP · If CHECK INPUT message also flashes, the digital connection is incorrect. 4 Play the source first to set the optimal recording level on the CD recorder. 5 Rotate the EASY JOG/ENTER key until all the blue segments are lighted on the Record/Play Level bar but the red segments do not light continuously during the loudest passages. Start recording 1 To start recording, press RECORD on the CD recorder and immediately start the source (from stop-mode). The track number and recording time will appear on the display. · To record a 3-second silence at the start of a track, press PAUSE on the CD recorder before starting the source. · To check the elapsed recording time, press DISPLAY on the CD recorder. (This can also be done during the recording. ) 2 To stop recording, press STOP on the CD recorder. · If STOP is pressed within 3 seconds after RECORD, no recording will take place. · To interrupt recording, press PAUSE on the CD recorder. After recording the display will show UPDATE for several seconds. DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL ·When Auto Track is On (default setting), track numbers will automatically be increased during recording. · To switch off the Auto Track function, you must enter Menu mode. If you wish to increase track numbers manually, press TRACK INCR(ement) on the remote control. ON (AUTO): The track increments are automatically copied from the digital source material or after 2. 7 second silence during analog recording OFF (MANUAL): Track numbers can be incremented manually by pressing TRACK INCR(ement) on the remote control. (Minimum track length is 4 sec. ) (This can also be done in Auto mode. ) · Track numbers cannot be changed after recording. Note: Auto track works only with Consumer Sources with a digital output signal according to the IEC 958 (consumer part) audio standard. Note: With AUTO TRACK ON, , the recorder will stop and go to REC STANDBY for 1 minute and then goes to stop mode automatically. Recordings from DAT, DCC or recordings made analogously will stop after 20 seconds of silence. With AUTO TRACK OFF, the auto stop mode is disabled. RECORDING Important: If you want to play the recorded CDR disc on a regular CD player, it must be finalized. Finalized CDRW discs play only on CDRW compatible CD players. · Use the LEVEL (Mic) key to mix your voice with the sound from the source. [. . . ] 7 By turning the EASY JOG key you can set the FADE IN or FADE OUT time. · FADE IN starts automatically when you press RECORD to start recording. Your recording will be faded out automatically when you press the STOP 9 or PLAY/PAUSE 2 ; key. 8 Press STORE/MENU to store settings and return to the submenu or STOP 9 to exit. DIGITAL I I OPTICAL I ANALOG CD PROGRAM RW MANUAL SYNC SCAN SHUFFLE REPEAT TRACK ALL 4 Press EASY JOG/ENTER or ENTER on the remote control to confirm. [. . . ]