User manual PHILIPS CE139DR

[. . . ] Always there to help you Register your product and get support at www. philips. com/welcome Question?Contact Philips CE139DR User manual Contents 1 Safety 2 Your car audio system Introduction What's in the box Overview of the system 2 3 3 3 4 6 7 8 9 10 10 10 11 11 11 11 12 12 12 12 12 12 13 15 15 15 15 16 16 16 16 17 17 17 EN 1 7 Play from a storage device Control play Switch tracks 17 18 18 19 19 19 19 20 20 21 21 21 21 22 23 24 25 25 25 25 8 Play from an iPod/iPhone 3 Install the car audio system Connect wires Mount into the dashboard Attach the front panel Compatible iPod/iPhone models Connect your iPod/iPhone Control play Charge your iPod/iPhone 9 Listen to an external player 10 Adjust sound 11 Additional information Reset the system Replace the fuse Upgrade the firmware 4 Get started For the first time use Set the time format Set the clock Select a source Select a listening zone Mute the button beep 5 Listen to FM/MW radio stations Switch to FM/MW radio mode Select a tuner region Select a tuner sensitivity Search for a radio station Store radio stations in memory Play with RDS 12 Product information 13 Troubleshooting 14 Notice Care of the environment Trademark notice Copyright 6 Listen to DAB radio stations Switch to DAB mode Scan for on-air stations Program radio stations Display DAB information Set up for weak reception Use the DRC (Dynamic Range Control) Disable the DAB reception Reset the DAB tuner Remove invalid stations Check the current version of DAB firmware 1 Safety Read and understand all instructions before you use this device. If damage is caused by failure to follow instructions, the warranty does not apply. • Modification of the product could result in hazardous radiation of EMC or other unsafe operation. [. . . ] When the traffic announcement is over, the system returns to the previous mode. • [TA OFF]: Traffic announcement does not cut in. Tip Use alternate frequencies If the signal of an RDS station is poor, enable the AF (Alternate Frequency) function to search for another station that broadcasts the same program. • When a traffic announcement cuts in, you can press to switch the system to the previous mode. 1 2 3 Press and hold menu. to access the system Synchronize the system clock You can synchronize the system clock with an RDS station that transmits time signals. Press / repeatedly until [AF ON] or [AF OFF] is displayed. • [AF OFF]: Disable the AF function. 1 2 3 Press and hold menu. to access the system 1 2 3 Set the region for AF tuning You can set the region for AF tuning. to access the system Press / repeatedly until [CT ON] or [CT OFF] is displayed. • [CT ON]: Synchronize the system clock with the RDS station automatically. • [CT OFF]: The automatic clock synchronization with RDS station is disabled. Tip Press / repeatedly until [REGION ON] or [REGION OFF] is displayed. • [REGION ON]: Only RDS stations in current region can be tuned to automatically. • [REGION OFF]: All RDS stations can be tuned to automatically. EN • The accuracy of time depends on the RDS station that transmits time signals. 14 6 Listen to DAB radio stations Note • Make sure that the DAB radio receiver is securely • For optimal reception, securely connect a DAB radio • connected. antenna to the DAB radio receiver and extend it. Check with local retailer or go to www. WorldDAB. org for applicable DAB radio frequencies in your area. Tune to a detected station 1 2 3 4 Press to exit the system menu. Press again to access the list of detected stations. / repeatedly or rotate until the name of the target station is displayed. Press Press to start listening. Program radio stations You can assign a sequence number to a detected station. Afterwards, you can quickly tune to it by pressing the corresponding numeric button on the main unit. Note • Before the programming, make sure that the scanning • You can store a maximum of six stations in each band. is complete. Switch to DAB mode 1 2 Press AS/SOURCE repeatedly to switch the source to [DAB/DAB+]. Press / repeatedly to select a band: DAB1, DAB2, or DAB3. Scan for on-air stations Program stations automatically Note • The operation does not replace the stations that are programmed in each band. 1 2 3 Press and hold to access the system menu. Press / repeatedly until [DAB STORE] is displayed. » The product starts programming DAB radio stations automatically. » Earlier programmed stations are replaced with the latest ones. » After the programming is complete, the first programmed station is broadcast. 1 2 Press and hold to access the system menu. » The product starts scanning for on-air DAB radio stations. » The detected stations are saved in the flash memory. EN 15 • To tune to a programmed radio station, press its corresponding numeric button , , , , , or . Set up for weak reception When the current reception gets poor, the product can automatically switch the source or mute the speakers according to your setup. Program stations manually 1 2 3 1 2 3 Tune to the target detected station (see ‘Tune to a detected station’ on page 15). Press and hold a numeric button , , , , , or to assign a sequence number to the station. [. . . ] • If the above solutions cannot help, press the RESET button. • Make sure that the current track is in a compatible format. Noise in broadcasts • Signals are too weak. Select other stations with stronger signals. [. . . ]