User manual PHILIPS CE153DR

[. . . ] Always there to help you Register your product and get support at www. philips. com/welcome Question?Contact Philips CE153DR User manual Contents Contents 1 Safety 2 Your car audio system Introduction What's in the box Overview of the system 2 3 3 3 4 6 7 8 10 11 11 11 11 11 12 12 12 12 12 13 13 13 13 7 Play from a storage device Control play Switch tracks 18 18 19 19 19 19 20 20 21 21 22 22 23 23 24 24 24 24 25 26 26 27 28 28 28 28 29 8 Play from an iPod/iPhone 3 Install the car audio system Connect wires Mount into the dashboard Attach the front panel Compatible iPod/iPhone models Connect your iPod/iPhone Control play Charge your iPod/iPhone 9 Use Bluetooth devices 4 Get started For the first time use Set the time format Set the clock Select a source Select a listening zone Mute the button beep Connect a device Play audio from a Bluetooth device Make a call 10 Listen to an external player 11 Adjust sound 12 Additional information Reset the system Replace the fuse Upgrade the firmware 5 Listen to FM/MW radio stations Switch to FM/MW radio mode Select a tuner region Select a tuner sensitivity Search for a radio station Store radio stations in memory Play with RDS 13 Product information 14 Troubleshooting 6 Listen to DAB radio stations 15 Switch to DAB mode 15 Scan for on-air stations 15 Program radio stations 16 Display DAB information 16 Set up for weak reception 17 Use the DRC (Dynamic Range Control) 17 Disable the DAB reception 17 Reset the DAB tuner 17 Remove invalid stations 17 Check the current version of DAB firmware 17 General About the Bluetooth device 15 Notice Compliance Care of the environment Trademark notice Copyright EN 1 1 Safety Read and understand all instructions before you use this device. If damage is caused by failure to follow instructions, the warranty does not apply. • Modification of the product could result in hazardous radiation of EMC or other unsafe operation. [. . . ] • To tune to a programmed radio station, press its corresponding numeric button , , , , , or . Program radio stations You can assign a sequence number to a detected station. Afterwards, you can quickly tune to it by pressing the corresponding numeric button on the main unit. Note • Before the programming, make sure that the scanning • You can store a maximum of six stations in each band. is complete. 4 Program stations automatically Display DAB information The name of current DAB station is displayed. You can also view the other information. To cycle through available information, press DISP repeatedly. • Dynamic label segment (DLS) • Signal strength • Program type (PTY) • Ensemble name • Frequency • Signal error rate • Bitrate codec • Time • Date 1 2 3 Press and hold to access the system menu. Press / repeatedly until [DAB STORE] is displayed. » The product starts programming DAB radio stations automatically. » Earlier programmed stations are replaced with the latest ones. » After the programming is complete, the first programmed station is broadcast. 16 EN Set up for weak reception When the current reception gets poor, the product can automatically switch the source or mute the speakers according to your setup. 3 1 2 3 Press and hold to access the system menu. Press / repeatedly until [DAB WEAK] scrolls. Rotate to select an option, and then press to confirm. • [WEAK MUTE]: Mute the speakers • [WEAK TO FM]: Switch the source to an FM radio station with strong reception that broadcasts the same program Rotate to select an option, and then press to confirm. • [ANTENNA OFF]: Disable the DAB reception. • [ANTENNA 12V]: Enable the DAB reception. Reset the DAB tuner 1 Press and hold to access the system 2 menu. Press / repeatedly until [DAB RESET] is displayed. • To clear the list of detected and programmed stations, press to confirm. • To exit the system menu, press . Use the DRC (Dynamic Range Control) DRC adds or removes a degree of compensation for the differences in the dynamic range between radio stations. Remove invalid stations 1 Press and hold to access the system 2 menu. Press / repeatedly until [PRUNE] is displayed. • To remove invalid stations from the list of scanned stations, press . • To exit the system menu, press . 1 2 Press and hold to access the system menu. Press / repeatedly until one of the following options is displayed. • [DRC OFF]: No compensation applied. [. . . ] • The device cannot be used with the system to play music. The audio quality is poor after connection with a Bluetooth-enabled device. Move the device closer to the system or remove any obstacle between the device and the system. • The device does not support the profiles required for the system. [. . . ]