User manual PHILIPS CID3290

[. . . ] Register your product and get support at www. philips. com/welcome CID3290 EN User manual 3 1 Important Safety Notice 4 4 4 2 Your in-car entertainment system Introduction What's in the box Overview of the main unit 5 8 Adjust sound 5 6 7 3 Get started Install the car audio Turn on Set date and time Adjust screen 8 10 10 11 8 Adjust volume Mute Select preset equalizer Adjust fader/balance Set Dynamic Bass Boost (DBB) 20 20 20 20 21 21 9 Adjust settings 4 Use map Upgrade the map 12 12 12 5 Listen to radio Tune to a radio station Store radio stations in memory Tune to a preset station 12 13 13 Display system setup menu Adjust general settings Adjust sound settings Adjust video settings Adjust Bluetooth settings Adjust language settings Adjust volume settings Adjust DVD rating 22 22 22 23 24 24 25 26 26 10 Others 6 Play Load discs Connect USB device Insert USB or SD/MMC card Play/Pause Skip/search Direct select Repeat one/all Repeat a section Random play Select audio language Select audio mode Select subtitle language Rotate pictures Zoom Select slide show duration 14 14 14 14 15 15 15 16 16 16 16 17 17 17 17 17 Listen to other devices Reset Replace fuse 27 27 27 27 11 Product information General Disc player Radio LCD Bluetooth 28 28 28 28 28 29 12 Troubleshooting 13 Glossary About Bluetooth device 30 31 30 EN 3 English Contents 7 Play with Bluetooth device Pair the Bluetooth-enabled devices Make a call Receive call Listen to music from Bluetooth device Adjust Bluetooth settings 18 18 18 19 19 20 1 Important Safety · Read and understand all instructions before you use the apparatus. If damage iscausedbyfailuretofollowinstructions, the warranty does not apply. Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. This unit is designed for negative ground (earth) 12 V DC operation only. [. . . ] Keep this unit away from any other electronic device that may cause interference. Turn on the Bluetooth function on the device. · The device will also be disconnected when the · If you want to reconnect the device to the unit, placeitwithintheoperationalrange. device is moved beyond the operational range. · If you do not want to reconnect the device to theunitautomatically, tap >[Auto connect], then select [Off]. Fordetails, seethe"Adjust Bluetoothsettings"section. Make a call 1 Pair the phone with the unit. 3 Tap [Bluetooth]. » The Bluetooth menu is displayed. 1 2 3 Search for Bluetooth device with the device. Select"CID3290"inthepairinglist. phone call record is displayed. 4 Tap or toselectthepairedphone, then tap . 18 EN 5 1 Duringtalking, tap . » The voice is transferred from the unit's loudspeaker to the mobile phone. · · · · · · Or tap to dial. [Missed calls] [Received calls] [Dialed calls] [Phone book] [Sim phone book] [Local phone book] todialnumberdirectly, thentap Listen to music from Bluetooth device If the connected Bluetooth device supports AdvancedAudioDistributionProfile(A2DP), you can listen to the music stored on the device through the unit. If the device also supports AudioVideoRemoteControlProfile(AVRCP) profile, youcanusethecontrolontheunitto play music stored on the device. Receive call Bydefault, allincomingcallsarereceived automatically. 1 Ifthereisincomingcall, [Incoming call. . . ] flashesonthescreen. Speakintothe Bluetooth microphone. 1 2 3 4 1 Pair the phone with the unit. » The Bluetooth menu is displayed. Tap . If your device support AVRCP. 2 Whenconversationends, tap to terminate the call. Tip (red) 2 Tap to start play. · You can select to receive calls manually by set [Auto answer] to [Off] status. EN 19 English Tap or to search for phone number from the following list: Switch phone call to the mobile If you do not want your passenger to hear yourincomingcall, youcanswitchthecallto the mobile. Adjust Bluetooth settings You can change below Bluetooth settings: · [Bluetooth]:toturnonoroff"Bluetooth" function · [Auto connect]: to turn on or off "Auto connect"function · [Auto answer]: to turn on or off "Auto answer"function · [Pairing code]: to set paring code · [Phone Book Sync]: to synchronize phone book 8 Adjust sound Adjust volume 1 Press VOL + to increase volume. · Press VOL - to reduce volume. 1 InBluetoothmenu, tap . » The option menu is displayed. Mute 1 Duringplay, press · Tip . Toturnthesoundbackon, press again. · You can also turn off sound by tapping the screen. on 2 Tap an option to change the setting. Tip Select preset equalizer You can select preset equalizer: · [User] · [Techno] · [Rock] · [Classic] · [Jazz] · [Optimal] · [Flat] · [Pop] · You can also adjust Bluetooth settings in the "Settings"menu. 1 2 Tap anywhere except for the upper left cornertodisplaymenuonthescreen, if necessary. » The current Equalizer setting is displayed. 20 EN Set Dynamic Bass Boost (DBB) 1 Tap to toggle between the settings. · · · · [DBB] on: The icon is illuminated. icon is [DBB] off (default): The gray. 5 6 Tap to restore the above settings into default settings. Tap to exit. Adjust fader/balance You can also adjust the front and rear speaker balance, theleftandrightspeakerbalance, and subwoofer settings. 1 2 3 Tap anywhere except for the upper left cornertodisplaymenuonthescreen, if necessary. Tap » Below options are displayed: 4 5 Tap or to select subwoofer volume. · [Sub] subwoofer volume: 0 to 24. Tap F, R, L, orR to adjust fader/balance value. · [Fade] fader range: +24 to -24. (F = frontspeaker, R=rearspeaker) · [Balance] balance range: -24 to +24. (L=leftspeaker, R=rightspeaker) EN 21 English 3 4 Tap Tap · · · · or to select an EQ. 6 Tap to exit. or to adjust below settings: [Bass] bass range: -14 to +14. [MPF]middlepassfilterrange:500, 1K, 1. 5K, 2. 5K. [HPF]highpassfilterrange:10K, 12. 5K, 15K, 17. 5K. 9 Adjust settings Display system setup menu 1 Tap to display main menu. General settings [Radio region] Options Description [Radio range] 2 Tap [Settings]. [. . . ] · Thedevicedoesnotsupporttheprofiles required for the system. · The Bluetooth function of the device is not enabled. Refer to the user manual of the device for how to enable the function. · The system is not in the pairing mode. [. . . ]