User manual PHILIPS COLOR TV 19 INCH PR1908B

[. . . ] Contact your dealer, or call our Parts Information Center at 1-800-851-8885 to order the following accessories: 300 (ohm) to 75 (ohm) adapter Combination VHF/UHF antenna. 8 8 M-Link +R L+ SURROUND SOUND Monitor out VIDEO Y L Pb AUDIO R Pr S-VIDEO AV1 in AV2 in ANT 75 Back of TV 300- to 75-Ohm Adapter 300 (Ohm) to 75 (Ohm) Adapter 1 Combination VHF/UHF Antenna (Outdoor or Indoor) TwinLead Wire OR 2 ANT 75 8 8 M-Link +R L+ SURROUND SOUND Monitor out VIDEO Y L Pb AUDIO R Pr S-VIDEO AV1 in AV2 in ANT 75 Back of TV Round Cable 75 (Ohm) TV TO VCR BASIC CONNECTION BEGIN F ollow the steps to the right to connect a basic antenna or cable TV signal to a VCR, and then the VCR to the TV. For information on other hookups (possible when cable/descrambler boxes are included), refer to the owner's manuals for the VCR and the cable converter. Connect your antenna or cable TV signal to the IN FROM ANT(enna) plug on the VCR. Outdoor VHF/UHF Antenna 300 (Ohm) to 75 (Ohm) Adapter Connect the OUT TO TV plug on the VCR to the 75 (ohm) plug on the TV (connecting cable supplied with the VCR). Refer to the owner's manual included with your VCR for other possible connections and TV/VCR operating details. 1 OR IN FROM ANT. OUT TO TV Round Cable 75 (Ohm) Supplied with VCR 2 ANT 75 8 8 M-Link +R L+ SURROUND SOUND Monitor out VIDEO Y L Pb AUDIO R Pr S-VIDEO AV1 in AV2 in ANT 75 Cable TV signal Back of TV VCR 1 3135 015 17701 TV AND REMOTE CONTROL OPERATION TELEVISION Press the POWER button to turn the TV ON. Press the VOL (+) button to increase the sound level or the VOL () button to lower the sound level. [. . . ] A/CH Press to toggle between the currently viewed channel and the previously viewed channel. Light Button Press to back-light the buttons on the remote control. PIP TV/VCR A/CH INCR. SURF SWAP SOURCE ON/OFF POSITION FREEZE Number Buttons Press the number buttons to select TV channels. When selecting single-digit channels, press the number of the desired channel. The TV will pause for a few seconds and then tune to the selected channel. (Note: You can press 0, then the number also. ) For channels 100 and above, first press 1 then the next two numbers of the desired channel. Incr. Button Press to set various factory Surround Sound listening modes. Surf Button Press to select previously viewed channels. You can place up to 10 channels in memory. Then by pressing the SURF button you can quickly view the select channels. (See the "Using the Channel Surf Control" section in your Instructions for Use manual to see how to select a series of channels using the Surf button. ) Picture Button Press to select an AutoPictureTM control. Choose from four factory-set controls (MOVIES, SPORTS, WEAK SIGNAL, and MULTI MEDIA) and a PERSONAL control that you set according to your own preferences through the onscreen PICTURE menu. The four factory-set controls will tailor the TV picture so as to enhance the particular type of program you are watching, or to improve the picture of the a program that has a weak signal. SOUND PICTURE Sound Button Press to select an AutoSoundTM control. It does not change the other onscreen text features, such as Closed Captioning (CC), with TV shows. Pressing the STATUS/EXIT button on your remote control after making adjustments to the TV will remove the menu from the screen. You also can back out of the menu by repeatedly pushing the MENU button on your remote control. CH 3 4 PRO OK GRA M LI ST OPEN /CLO SE TUNER T he TUNER feature allows you to change the TV's signal input to CABLE, ANTENNA, or AUTO mode. Press the CURSOR RIGHT button to start the Auto Program scanning of channels. Press the STATUS/EXIT button to clear the menu from the screen. PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER AUTO PROGRAM CHANNEL EDIT AutoChron SLEE P 1 4 7 SOU ND TV A/C /VCR H INC R. SUR R. INSTALL LANGUAGE TUNER AUTO PROGRAM CHANNEL EDIT AutoChron ON/O POW FF POSI 1 2 5 8 0 PIC M-L INK SUR F SW AP TIO N PIP FRE EZE ER INSTALL LANGUAGE TUNER AUTO PROGRAM CHANNEL EDIT AutoChron SEARCH INSTALL LANGUAGE TUNER AUTO PROGRAM CHANNEL EDIT AutoChron CABLE PLEASE WAIT CHANNEL 12 SOU RCE 3 6 9 TUR E MEN U SMART HELP VOL SOU ITR /RE RCE MU STAT U S/EX IT CC E HOM E MO VIE S PER SON AL CLO CK TE CH 3 2 4 C HOM 5 VID EO PRO GRA OK M LI ST OPEN /CLO SE 6 After youve run Auto Program, check out the results. Press the CHANNEL (+) or () button and see which channels you can select. 3 Remember, an antenna or cable TV signal must first be connected to your TV (see instructions for making connections on page 1 of this guide). If you want to delete any unwanted channels from the TVs memory, see the CHANNEL EDIT section on page 4. HOW TO USE THE INSTALLATION FEATURES CHANNEL EDIT HANNEL EDIT makes it easy for you to add or delete channels from the list of channels stored in the TVs memory. C Press the MENU button on the remote control to show the onscreen menu. Press the CURSOR DOWN button repeatedly until INSTALL is highlighted. Press the CURSOR RIGHT button to shift the menu to the left. Press the CURSOR DOWN button repeatedly until the CHANNEL EDIT control is highlighted. Press the CURSOR RIGHT button to access the CHANNEL EDIT menu. Press the CURSOR UP or CURSOR DOWN button to scroll through the list of available channels. Or press the number buttons on your remote control to select a specific channel (for example, press 0 and then 2 to select channel 2). With the channel you want to edit selected, press the CURSOR RIGHT button to mark the channel as SKIPPED. The channel youve marked SKIPPED will not appear when you are changing from channel to channel while watching TV. [. . . ] LANGUAGE will be highlighted. Press the CURSOR DOWN button until the AutoChron control is highlighted. Press the CURSOR RIGHT button to start the AutoChronTM feature. Then just follow the onscreen instructions to set the clock. Press the CURSOR RIGHT button to select AUTO. [. . . ]