User manual PHILIPS CRA01

[. . . ] This guide will provide the basic steps for installing the LT card into a Philips SmartCard-enabled display. B. Package Contents Your CRA01/00 package should contain the following: 1 x LT card module 1 x LT card cap (see Fig. 1 below) 1 x VGA cable (30cm/ 11. 811") 1 x RS232 cable (20cm/ 7. 874") Installation Guide (this document) Global Warranty Card Fig. [. . . ] Ensure that the card is securely connected to the internal 32-pin socket. 8. Secure the LT card to the display by re-fastening the screws that were removed in step 4. Screws to be fastened 9. Use the included VGA cable to connect the VGA Local on the LT card to the VGA In on the display as shown. 10. Use the included RS232 cable to connect the RS232 Local on the LT card and the RS232 In on the display as shown. Page 5 of 9 LT Installation Guide 1. 1 (140907) 12NC: 3139 125 39281 F. VGA The diagram below illustrates the VGA connection configuration to a PC and multiple displays. Important note: The VGA cable from the PC to the first display should be type E101344 with all 15 pins available to ensure EDID read out. BDLX231 VGA In *DB15 M-M 1 CRA01 BDLX231 VGA In *DB15 M-M 1 CRA01 BDLX231 VGA In *DB15 M-M 1 CRA01 23 23 23 DB15 M-M DB15 M-M DB15 M-M Legend: 1 ­ VGA Local 2 ­ VGA In 3 ­ VGA Out * cable provided Page 6 of 9 LT Installation Guide 1. 1 (140907) 12NC: 3139 125 39281 2. RS232 (Serial Communications) The diagram below illustrates the RS232 connection configuration to a PC and multiple displays. BDLX231 RS232 In *DB9 F-M (cross cable) 4 CRA01 BDLX231 RS232 In *DB9 F-M (cross cable) 4 CRA01 BDLX231 RS232 In *DB9 F-M (cross cable) 4 CRA01 56 56 56 DB9 F-F (cross cable) DB9 F-F (cross cable) DB9 F-F (cross cable) Legend: 4 ­ RS232 Local 5 ­ RS232 In 6 ­ RS232 Out * cable provided G. Troubleshooting There is no image on the "head" display (the unit that initially receives source input) 1. Make sure that the VGA input has been selected on the display. Double-check the local connection: Is the VGA Local on the LT card properly connected to the VGA input on the display?If there is still no image check the PC output by directly connecting the PC's VGA cable to the display's VGA input. If there is an image on the screen this may indicate a defective card. If after Step 3 there is still no image then swap the display with another display that has been proven to function properly and re-install the LT card. If after Step 4 there is still no image, swap the LT card with a card that has been proven to function properly. If there is still no image after following the preceding steps, the LT card is probably defective. Please consult the product's Warranty Card for service instructions. Page 7 of 9 LT Installation Guide 1. 1 (140907) 12NC: 3139 125 39281 The "head" display is working, but the next display (Display 2) doesn't show an image. Make sure that the VGA input has been selected on Display 2. Double-check the local connection: o Is the VGA Local properly connected to the VGA input on the "head" display? [. . . ] There are cable quality dependencies and the system integrator will need to try out which is the optimal baud rate for the installed network. How many units can be daisy chained For VGA the product has been tested up to 5 displays. More units can be daisy chained but some picture quality degradation may be visible. [. . . ]