User manual PHILIPS CSS9216

[. . . ] Register your product and get support at www. philips. com/welcome CSS9216 User manual Benutzerhandbuch Mode d'emploi Brukerhåndbok Manual del usuario Användarhandbok Brugervejledning Gebruiksaanwijzing Manuale utente Manual do utilizador Käyttöopas Kullanim kilavuzu Contents 1 Help and support FAQs Contact Philips 2 2 2 2 2 3 3 3 3 4 4 5 5 5 5 6 6 7 8 8 8 13 13 14 14 8 Setup menu options and settings Apply factory settings 2 Compliance Mains fuse Trademarks Notice Check software version Update software through computer Update software 17 17 17 17 18 19 9 Product specifications 3 Safety Care for your product Care of the environment Important 10 Troubleshooting 11 Index 4 Main unit Subwoofer Remote control Your SoundHub 5 Connect speakers Connectors Connect audio from TV and other devices Listen to a connected device Connect to a Wi-Fi network Connect your SoundHub 6 Choose your sound MP3 player Play audio from an AirPlay device Use your SoundHub EN 1 English 7 Change settings 15 15 16 1 Help and support 2 Notice FAQs If you have a problem, refer to the frequently asked questions (FAQs) for this SoundBar at www. If you still need help, contact Philips Consumer Care in your country. Warning · Do not attempt to repair your SoundBar yourself. This may cause severe injury, irreparable damage to your SoundBar, or void your warranty. This section contains the legal and trademark notices. Compliance This product is in compliance with the essential requirements and other relevant provisions of Directives 2006/95/EC (Low Voltage), 2004/108/ EC (EMC). Contact Philips If you contact Philips, you will be asked for the model and serial number of your product. [. . . ] Connect to the power supply. Side right EN 7 Connect audio from TV and other devices Play audio from TV or other devices through your SoundHub. Use the best quality connection available on other devices. Note · The audio connections in this user manual are only recommendations. You can use other connections too. Option 3: Connect audio through analog audio cables Basic quality audio Using an analog cable, connect the AUX connectors on your SoundHub to the audio connectors on the device. VCR Option 1: Connect audio through a digital optical cable Best quality audio Using an optical cable, connect the OPTICAL connector on your SoundHub to the OPTICAL OUT connector on the device. The digital optical connector might be labeled SPDIF, SPDIF OUT, or OPTICAL. Listen to a connected device Before you can listen to a connected device, select the source for the device. Option 1: Connect SoundHub to a WPS router Wi-Fi protected setup (WPS) enables you to connect devices to your router without a password. Simply enable the WPS function on both the router and your SoundHub and they are connected. Most of the WPS router carry the WPS logo: . Press and hold SETUP for five seconds to switch to the WPS mode. » PRESS WPS BUTTON ON ROUTER AND WAIT is displayed on the display panel. Option 2: Connect SoundHub to a non WPS router Connect your SoundHub to a non WPS router through an AirPlay enabled device. Press SETUP repeatedly to select WIFI on the display panel. Press the Navigation buttons ( / ) to select BROWSER SETUP, and then press OK. » First, PLEASE WAIT is displayed on the display panel and the subwoofer LED indicator blinks continuously. 1 2 3 1 4 » Then, the SoundHub creates a virtual network and SELECT PHILIPS AIRPLAY NETWORK AND BROWSE 192. 168. 1. 12 is displayed on the display panel. When you connect your AirPlay enabled device to this network, you can access the SoundHub setup web page. On your iPod Touch, iPhone or iPad, select Settings > Wi-Fi. · On your Wi-Fi enabled computer, select the list of available wireless networks. 2 3 » The subwoofer LED indicator blinks continuously. Within ninety seconds, press the WPS button once on the router. When the connection with the router is established, WPS SUCCESS is displayed on the display panel. EN 9 English 6 On your iPod Touch, iPhone or iPad, open Safari (Safari) to access the configuration page. Enter the IP address 192. 168. 1. 12 at the address bar. · On your computer, open the web browser and enter 192. 168. 1. 12 at the address bar. » The SoundHub web page is displayed. This page allows you to configure the SoundHub by connecting it to your home network. 5 192. 168. 1. 12 Select Philips SoundHub AirPlay (Philips SoundHub AirPlay) from the list of available wireless networks. Philips SoundHub AirPlay 7 Philips SoundHub AirPlay From the Philips SoundHub web page, select the Network Configuration (network configuration) tab. 10 EN Network Configuration 8 Select your router SSID from the pull-down list of Service Set ID (SSID) (service set ID). 10 Click Apply (apply) at the bottom of the page to apply your settings. » A menu for confirmation of your settings pops up. 192. 168. 1. 12 192. 168. 1. 12 1 9 Enter your network key if required. · For some routers, you may also need to tick DHCP under Advance Setting (advance setting). 11 Click OK on the popup menu to confirm your settings. EN 11 English 1 On your iPod Touch, iPhone, or iPad. · On your computer, select the list of available wireless networks. 192. 168. 1. 12 » CONNECTING is displayed on the display panel. [. . . ] · On your remote control, press AUX, COAXIAL/OPTICAL, or MUSIC iLINK repeatedly to select the correct audio input on the display panel (see 'Listen to a connected device' on page 8). · If you play audio from the TV through the SoundHub, make sure that the TV is muted. 2) Within two seconds, press the Navigation buttons ( / ) to change the delay shown on the display panel. 3) Press AUDIO SYNC again to exit. Play AirPlay icon does not appear in iTunes. [. . . ]