User manual PHILIPS DCB2020

[. . . ] Register your product and get support at www. philips. com/welcome DCB2020 EN User manual Contents 1 Important Important notes for users in the U. K. Safety 4 4 4 7 Listen to radio Store DAB radio stations automatically Basic operations Use the menu 15 15 15 15 2 Your Micro Music System Introduction What's in the box Overview of the remote control Overview of the main unit 6 6 6 6 8 8 Other features Set sleep timer Set alarm timer Listen to external audio device Listen through headphone 16 16 16 17 17 3 Before use Place the product Connect speakers Connect power Install/replace the remote control batteries 9 9 9 10 10 8SJUDGH WKH ÀUPZDUH Register your product &KHFN WKH FXUUHQW ÀUPZDUH YHUVLRQ Perform the upgrade 17 18 10 Product information 4 Get started Turn on Set clock Demonstrate features 18 19 19 19 11 11 11 11 6SHFLÀFDWLRQV USB playability information Supported MP3 disc formats RDS program types 11 Troubleshooting 5 Play Play a disc Play from a USB storage device Basic control Program audio tracks Adjust sound 21 22 22 22 22 22 12 12 12 12 12 13 12 Notice Compliance Disposal of your old product and batteries Copyright Trademark 6 Play from iPod/iPhone/iPad Compatible iPod/iPhone/iPad Load the iPod/iPhone/iPad Charge the iPod/iPhone/iPad Listen to the iPod/iPhone/iPad Remove the iPod/iPhone/iPad 13 13 13 14 14 14 EN 3 1 Important Read and understand all instructions before you use this product. If damage is caused by failure to follow the instructions, the warranty does not apply. Safety Risk of electric shock! Never expose the product and accessories to rain or water. [. . . ] Keep batteries away from heat, VXQVKLQH RU ÀUH 1HYHU GLVFDUG EDWWHULHV LQ ÀUH Note If you are not going to use the remote control for a long time, remove the batteries. Do not use old and new or different types of batteries in combination. Batteries contain chemical substances, so dispose of them properly. 10 EN 4 Get started Caution Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Set clock 1 In standby mode, press and hold PROG/CLOCK SET to activate clock setting. » [CLOCK SET] (set clock) scrolls on the display, and then [CLOCK 24] KRXU WLPH IRUPDW LV GLVSOD\HG ZLWK "24" blinking. Press / or VOL +/- to select [CLOCK 24] or [CLOCK 12] KRXU WLPH IRUPDW DQG WKHQ SUHVV PROG/CLOCK SET. » The minute digits begin to blink. Press PROG/CLOCK SET WR FRQÀUP WKH clock setting. To exit clock setting without storing, press . Note If no button is pressed in 90 seconds, the system exits clock setting mode automatically. Always follow the instructions in this chapter in sequence. 2 Turn on Press . » This product switches to the last selected source. 3 4 5 6 6ZLWFK PRGHV $XWRPDWLFDOO\ VZLWFK WKH PRGHV After this product keeps inactive for 15 minutes, it automatically switches to the normal standby mode. » [PRG] blinks on the display panel. Repeat steps 3 and 4 to program more tracks. To erase the program, press twice. NTFS (New Technology File System) data format is not supported. 12 EN Note The programmed tracks must be stored on the same disc or USB storage device. You can program a maximum of 20 tracks. 6 Play from iPod/ iPhone/iPad You can enjoy audio from iPod/iPhone/iPad through this product. Adjust sound Note During play, you can adjust the volume level and sound effect through following operations. Button Function No audio output from the headphone socket in this situation. VOL +/DBB Increase or decrease the volume. Turn on or off the dynamic bass enhancement (DBB). If DBB is activated, [DBB] is displayed. Select a sound effect: [POP] (pop), [JAZZ] (jazz), [ROCK] (rock), [CLASSIC] (classic), or [FLAT] ÁDW Compatible iPod/iPhone/iPad This product supports the following iPod, iPhone and iPad models. iPad 2 iPad iPhone 4 iPhone 3GS iPhone 3G iPhone iPod touch (1st, 2nd, 3rd, and 4th generation) iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generation) iPod classic iPod with video iPod with color display iPod mini DSC Load the iPod/iPhone/iPad Note The peak current through the dock connector is limited as 1000 mA for iPod/iPhone and 2100 mA for iPad/ iPad 2. To avoid damage to your iPod/iPhone/iPad and this product, securely load your iPod/iPhone/iPad as indicated. 1 Push the lock key to release the dock lid. EN 13 2 Insert your iPod/iPhone/iPad onto the dock. Charge the iPod/iPhone/iPad When the product is connected to power, the docked iPod/iPhone/iPad starts charging automatically. Tip For certain iPod models, it may take up to a minute before the charging indication appears. Listen to the iPod/iPhone/ iPad Install the rubber bumper Note If your iPad 2 is not in a case, use the supplied rubber bumper to keep it stable. 1 2 Press DOCK to select the iPod/iPhone/ iPad source. Select and play a track on your iPod/ iPhone/iPad. To skip to the previous or next track, press /. To search during play, press and hold / , and then release it to resume normal play. To access the playlist of iPod/iPhone, press Menu/ . To access the playlist of iPad/iPad 2, operate on the iPad/iPad 2 screen. To scroll through the playlist, press / . 7R FRQÀUP DQ RSWLRQ SUHVV OK on the remote control. 1 Release the dock lid, and then place the rubber bumper onto the dock compartment. 2 Load your iPad 2. Remove the iPod/iPhone/iPad 1 2 Pull the iPod/iPhone/iPad out of the dock. [. . . ] Make sure that the speakers are connected correctly. Make sure that the stripped speaker wires are clamped. No response from the Reconnect the AC power plug, and then turn on the product again. product :LWK D SRZHUVDYLQJ IHDWXUH WKH V\VWHP VZLWFKHV RII DXWRPDWLFDOO\ PLQXWHV after the product stays inactivity. [. . . ]