User manual PHILIPS DCB242

[. . . ] Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. i j k l m Battery usage CAUTION ­ To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: · Install all batteries correctly, + and - as marked on the unit. · Do not mix batteries (old and new or carbon and alkaline, etc. ). · Remove batteries when the unit is not used for a long time. [. . . ] Select a preset sound setting. · m REP AL/BRIGHTNESS · Adjust the display brightness. · Repeat the alarm. n · · o SET TIME/AUTO SCAN Set the time and date. FM/DAB Select the FM tuner/DAB source. · 3 Get started Caution · Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the rear of the apparatus. ___________________________ Install batteries Note · You can only use AC power as power supply. Batteries (not supplied) are for backup purpose. R6/UM-3/AA 3x1. 5V 1 2 3 Open the battery compartment. Insert 3 x AA batteries with correct polarity (+/-) as indicated. Close the battery compartment. Prepare the remote control Caution · Risk of explosion!Keep batteries away from heat, sunshine or fire. For first-time use: 1 Remove the protective tab to activate the remote control battery. To replace the remote control batteries: 1 2 3 Open the battery compartment. Insert one lithium CR2025 battery with correct polarity (+/-) as indicated. Note · Before you press any function button on the remote control, first select the correct source with the remote control instead of the main unit. Connect power Caution · Risk of product damage!Ensure that the power voltage corresponds to the voltage printed on the back or underside of the apparatus. When you unplug the AC adaptor, always pull the plug from the socket. · Before connecting the AC adaptor, ensure that you have completed all other connections. · Use the supplied AC power adaptor only. Note · The type plate is located on the bottom of the main unit. 1 Connect the AC power adaptor to: · the DC socket on the main unit · the power socket. FM ANT MP3-LINK DC 9V 1. 9A DC 9V 1. 9A Set time and date 1 In standby mode, press and holdSET TIME/AUTO SCANfor 2 seconds. » [SYNC ON] is displayed and [ON] begins to blink. 2 PressPRESET + /PRESET - to select ON or OFF. » If you select [ON], the unit reads the DAB station or iPhone/iPod time and sets the clock automatically. » If you select [OFF], the unit turns off the time synchronization. » 3 Press SET TIME/AUTO SCANto confirm. The time format [24H] or [12H] begins to blink. 4 PressPRESET + /PRESET - to select 24H or 12H. » 5 Press SET TIME/AUTO SCANto confirm. The hour digits begin to blink. 6 Repeat steps 4-5 to set the hour, minute, year, month, and day. Tip · The accuracy of the transmitted time depends on the DAB station or the docked iPhone/iPod that transmits the time signal. Turn on 1 Press POWER on the remote control. » The unit switches to the last selected source. Switch to standby 1 Press POWER again to switch the unit to standby mode. » The time and date (if set) appear on the display panel. 4 Play Play from iPod/iPhone You can enjoy audio from iPod/iPhone through this unit. Compatible iPod/iPhone Apple iPod and iPhone models with a 30-pin dock connector: Made for. [. . . ] When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. No power · Ensure that the AC power plug of the unit is connected properly. · Ensure that there is power at the AC outlet. · Ensure that the batteries are inserted correctly. [. . . ]