User manual PHILIPS DECT 215

[. . . ] Installing your telephone Inserting / Replacing battery pack / Telephone connection Warning:To insert battery pack and /or to connect your telephone, please refer to the drawings printed on the inside cover. With the help of the installation drawings : 1. - Plug the line cord (A) into the line socket on your DECT 211 or DECT 215 base station. Plug the power cable (B) into the power socket on your DECT 211 or DECT 215 base station. Plug the power supply unit into the wall socket. [. . . ] Intercom & call transfer are only possible with handsets* registered to the same base station. Fast call transfer During a call in progress you can transfer the call without waiting for the other handset to pick up : All the handsets ring. . Call transfer to a specific handset During a call in progress you transfer the call to a specific handset : Long press on enter the handset number (1 to 4) Paging This feature allows you to locate the handset(s). Press on the base station, all the subscribed handsets ring. Once again. located, press any key on the handset to stop ringing or press 8 www. philips. com/faqs/dect Using your answerphone Setting up the answerphone The answerphone is by default activated with a pre-recorded message and the answer & record mode. (standard quality) - 6 min (high quality) : including personal outgoing message if recorded. Activating the answerphone beep To exit Deactivating the answerphone beep To exit Playing new messages / playing a memo . You can adjust the volume using Playing your old messages or previous or next message Deleting the current message listen to the message Deleting all messages Long press . To exit To exit When playing a message, the date and time of the message are displayed on the handset. icon is Playing the current outgoing message the outgoing message is played . To exit www. philips. com/faqs/dect 9 Recording your personal outgoing message speak after the beep * To exit However, if you do so, you will permanently erase the pre-recorded outgoing message. Recording a memo If you want to leave a local message for your family : speak after the beep To exit Selecting the answerphone mode You can select either answering mode only (which plays an outgoing message but does not take messages) or answering & recording mode (which takes messages. ) or to switch between modes To exit answering & recording mode answering only mode *You will hear the personal outgoing message. This local message (memo) is treated like all other answerphone messages. Advice: prior to using the answering-only mode, make sure that you have adapted the outgoing message. Screening the calls while a message is being left This allows you to listen to any caller leaving a message and to decide whether or not to take the call. Activating call screening From the handset : Deactivating call screening From the handset : Increasing the volume of the call screening During call screening, the volume can be adjusted. 4 volume levels are available, including silent. Press until you have reached the desired volume. The last selected level will be registered for the next call. When the answerphone is on-line, blinks. Call interception The recording of the current message is stopped and the call is taken. 10 www. philips. com/faqs/dect Remote access This allows you to remotely dial in and access your answerphone via any telephone with a key and tone dialling. Scroll to the required number of rings with and validate with . or ** :In toll saver mode, if there are new messages the answerphone will answer after 3 rings, and only after 5 rings if there are no new messages. So, you can hang up after 4 rings without paying for a call. Toll saver is useful for remote access only. 12 www. philips. com/faqs/dect Changing Remote Access Code (option 4/5) To remotely access your answerphone you need to enter a secret code (4 digits). By default, this code is identical to the RC code written under the base. If you want to change the default code : Enter a personal code and press to validate. Note : You can delete with your Remote Access Code. [. . . ] - Register the handset to the base station. (p 14) - Move closer to the base station. - Take the handset off the base station and put it back again. - Clean them with a clean and dry cloth. [. . . ]