User manual PHILIPS DECT5150S

[. . . ] If you register the additional handset to another Philips base station, only a limited number of menus will be available. Please refer to the corresponding complete set user guides. Using a non-Philips GAP base station To register the Philips additional handset to a non-Philips base station, follow the base station instructions described by the other manufacturer. Then follow the instructions on page 5 to register the Philips additional handset. There will be only a few menus available. Philips has marked the battery and packaging with standard symbols designed to promote the recycling and appropriate disposal of your eventual waste. The labelled packaging material is recyclable. A financial contribution has been paid to the associated national recovery & recycling system. DECT is a trade mark of ETSI registered for the benefit of the implementers of the DECT technology TM Conformity, Environment & Safety 1 English Pilot key Press to enter the carousel or select a menu or an option Scroll to move through the menus & options or move the cursor left or right Scroll up to reach Call log from idle mode Scroll down to reach Phonebook from idle mode Long press to unlock the keypad Loudspeaker - Press to take the line or activate the handset loudspeaker during a call - A long press to activate the base loudspeaker when listening to a message (DECT 515 only) Keypad lock & Edition - Short press to insert * - Long press to lock/unlock the keypad - Long press to insert R (inbetween digit pause) when dialling - Long press to enter multitap mode or Eatoni® editor when editing - Short press to change the letter when editing in Eatoni® SMS key - Short press to directly access Send new SMS from idle mode - Short press from the Phonebook or the Call log menu to edit an SMS Line key - Press to take the line, answer a call or hang up. [. . . ] The handset display 3 , new SMS or new English , if any, "Do Not Disturb" mode press or , if activated (To activate/deactivate these functions Installing and replacing the batteries in the handset To insert the batteries, open the battery cover, place the batteries as indicated and put the battery cover back. When the handset is placed on the base station the 3 battery bars scroll (if charge is needed). Allow the handset to charge for 24 hours to reach full charge. On first use it may be necessary to wait for a few minutes before seeing symbols on the display. In case you need to change the batteries, the following type is mandatory 2HR AAA NiMh 600 mAh. Warning: the base station must always be plugged into the mains when charging or when in use. Batteries should not be disposed of with general household waste. Battery life and range A battery low alert will inform you that the batteries have to be recharged. If it happens during a call, the communication will be shortly cut. Optimal battery life is reached after 3 cycles of complete charge & discharge. When reaching the range limit and the conversation becoming crackly, move closer to the base. To reach optimal range, place the base station away from electrical appliances. Battery life in standby mode up to 200 hours Battery life in communication up to15 hours Indoor range up to 50 metres Outdoor range up to 300 metres Understanding the menu system To access the carousel menu from idle mode, press on the side of the handset The carousel represents a loop of icons that gives access to the different first level menus. Scroll up or down to reach the desired menu and select The sub menus are listed and represented by little squares at the bottom of the display. To reach one particular sub-menu use the "pilot key" and press to validate your choice. A "tick" shows the selected sub-menu or option. The shows the option you are browsing. Note: some menus are also directly accessible via a dedicated key on the keypad like the SMS menu with Direct dialling Take the line and dial on the keypad 4 or the Intercom with . Predialling Dial on the keypad and take the line Batteries and menu system Handset Registration The additional handset will get full capability when it is registered to the base station (see p. You can register up to 6 handsets to the DECT 511 or DECT 515 base station. To register a handset Unplug and plug back in the mains supply to put the base in registration mode With the additional handset, press to start the registration Enter the 4-digit RC code written on the sticker placed under the base station and press OK To unregister a handset Press to enter the carousel menu Scroll to Handset and select Scroll to Registration and select Scroll to Un-register handset and select Choose the handset to un-register from the list and press Enter the 4-digit RC code and press OK OK Note: should you have your handset serviced alone, please make sure it is unregistered from the base station before taking it back to the repair centre. Babysit mode if there are at least 2 handsets This feature allows you to monitor the baby's room. Place the handset in the room to be monitored and you will hear the noise coming from the room on the additional handset. English 5 To activate/deactivate the babysit mode Press to enter the carousel menu Scroll to Handset and select Press to select Babysit mode Select ON or scroll to OFF and select Note: an intercom is necessary to monitor the room (see page 8). Handset Rename handset To rename a handset Press to enter the carousel menu Scroll to Handset and select Scroll to Rename handset and select Long press to delete the current name Enter the name and press OK Language To change the language Press to enter the carousel menu Scroll to Handset and select Scroll to Language and select Browse through the list and select Date & time To set the date and time Press to enter the carousel menu Scroll to Handset and select Scroll to Date & time and select Select Set date Enter the current date and press Scroll to Set time and select Enter the current time and press OK OK 6 Handset Display contrast To set the display contrast Press to enter the carousel menu Scroll to Handset and select Scroll to Display contrast and select Browse through the levels and select the appropriate one Backlight To set the display backlight duration or deactivate it Press to enter the carousel menu Scroll to Handset and select Scroll to Backlight and select Browse through the durations OFF / 10 seconds / 20 seconds and select Screen saver After 2 minutes of inactivity, the screen saver is displayed. You can choose to activate or deactivate it To activate or deactivate the screen saver Press to enter the carousel menu Scroll to Handset and select Scroll to Screen saver and select English 7 Press to select ON or scroll to OFF and select Handset Intercom Using the Intercom (if there are at least 2 handsets) This feature allows you to make free internal calls, transfer external calls from one handset to another, use the conference option and the babysit feature (room monitoring). Internal call Press to call the selected handset + handset number (for example Hang up Note: if the handset does not belong to the Philips DECT 511/515 range, this function may not be available. ) Fast call transfer when on line During a call you can transfer the call without waiting for the other handset to pick up. Press to call the other handset Hang up Note: the person on hold hears music. A press on allows you to switch between the 2 calls. Call transfer to a specific handset when on line During a call you can transfer the call to a specific handset. Press to call the selected handset + handset number (for example Hang up Note: the person on hold hears music. A press on allows you to switch between the 2 calls. [. . . ] Wait until it is available Move closer to the base Charge the batteries. Un-register a handset (page 5) The batteries remain low although they have charged for 12 hours. The batteries are defective or too old. An error beep is heard from Another call is already in the handset when trying to progress from another handset make a call. The base is being consulted An error beep is heard The handset is out of range. [. . . ]