User manual PHILIPS DECT5250S

[. . . ] Environmental care: please remember to observe the local regulations regarding the disposal of your packaging materials, exhausted batteries and old phone and where possible promote their recycling. Using GAP standard compliance TM The GAP standard guarantees that all DECT GAP handsets and base stations comply with a minimum operating standard irrespective of their make. Your handset is GAP compliant, which means the minimum guaranteed functions are : take the line, receive a call and dial. Using Philips base stations If you register the additional handset to a Philips DECT 521 or DECT 525 base station, the handset will have all the features described in the corresponding complete set user guide. If you register the additional handset to another Philips base station, only a limited number of menus will be available. Please refer to the corresponding complete set user guides. Using a non-Philips GAP base station To register the Philips additional handset to a non-Philips base station, follow the base station instructions described by the other manufacturer. Then follow the instructions on page 5 to register the Philips additional handset. There will be only a few menus available. Philips has marked the battery and packaging with standard symbols designed to promote the recycling and appropriate disposal of your eventual waste. The labelled packaging material is recyclable. [. . . ] A tick shows the selected sub-menu or option. The shows the option you are browsing. Note: some menus are also directly accessible via a dedicated key on the keypad like the Intercom with , the phonebook with and the call log with . Direct dialling Take the line and dial on the keypad 4 Predialling Dial on the keypad and take the line Batteries and menu system Handset Registration The additional handset will get full capability when it is registered to the base station (see p. You can register up to 6 handsets to the DECT 521 or DECT 525 base station. Unplug and plug back in the mains supply to put the base in registration mode and start the following procedure immediately after that. Scroll to Handset and press Scroll to Registration and press to select. to select. To register a handset Press to select Register handset. Enter the 4-digit RC code written on the sticker placed under the base and press . To unregister a handset Press to enter the carousel menu. Scroll to Handset and press Scroll to Registration and press to select. . Scroll to Un-register handset and press Choose the handset to un-register from the list and press Enter the 4-digit RC code and press . Note: should you have your handset serviced alone, please make sure it is unregistered from the base station before taking it back to the repair centre. Babysit mode if there are at least 2 handsets This feature allows you to monitor the babys room. Place the handset in the room to be monitored and you will hear the noise coming from the room on the additional handset. To activate/deactivate the babysit mode Press to enter the carousel menu. Scroll to Handset and press Press to select Babysit mode. Select ON or scroll to OFF and press Handset to confirm. 5 Note: an intercom is necessary to monitor the room (see page 8). to select. Rename handset To rename a handset Press to enter the carousel menu. to select. Scroll to Rename handset and press Long press to delete the current name. Enter the name and press . Language To change the language of the display Press to enter the carousel menu. Scroll to Handset and press Scroll to Language and press to select. . Browse through the list and select with Date & time To set the date and time Press to enter the carousel menu. to select. Scroll to Date & time and press Select Set date. Enter the current date and press Scroll to Set time and press Enter the current time and press . to select. . 6 Handset Display contrast To set the display contrast Press to enter the carousel menu. the appropriate one. Scroll to Display contrast and press Browse through the levels and select with Backlight To set the display backlight duration or deactivate it Press to enter the carousel menu. [. . . ] An error beep is heard from Another call is already in Retry when the current call is the handset when trying to progress from another handset finished. An error beep is heard Move closer to the base. When adding a handset to the base station, a failure message is displayed. The maximum number of handset has been reached. [. . . ]