User manual PHILIPS DS-9800W

[. . . ] Register your product and get support at www. philips. com/welcome DS9800W EN User manual Contents 1 Important Safety Notice 4 4 5 7 7 7 7 8 8 9 10 10 13 13 18 19 19 20 20 20 21 22 22 23 2 Your Docking Entertainment System Introduction What's in the box What else you need Overview of the SoundSphere Speakers Overview of the remote control Overview of the docking charger 3 Prepare Connect 4 Set up a Wi-Fi network for AirPlay Connect speakers to a Wi-Fi network (router) Connect an AirPlay device to the same Wi-Fi network 5 Play Stream audio from your AirPlay device Control play Advanced sound settings Update firmware Charge your iPod/iPhone/iPad with the standalone dock 6 Product information Specifications 7 Troubleshooting EN 3 1 Important Safety Mains fuse This information applies only to products with a UK mains plug. This product is fitted with an approved molded plug. If you replace the fuse, use one with: · the ratings shown on the plug, · a BS 1362 approval, and · the ASTA approval mark. Contact your dealer if you are not sure about what type of fuse to use. [. . . ] Insert fully the end of a speaker cable with red mark into the left red (+) connector. Screw the left red (+) connector to secure the cable. Insert fully the end of a speaker cable without red mark into the left black (-) connector. EN Connect power Caution · Risk of product damage!Ensure that the power · · supply voltage corresponds to the voltage printed on the bottom of the unit. When you unplug the AC power cord, always pull the plug from the socket. Before connecting the AC power cord, make sure that you have completed all the other connections. Connect power to standalone docking charger (optional) UK EUR Connect power to speakers ON/OFF · To charge your iPod/iPhone/iPad, connect the AC power cord to · the ~ DC IN socket on the docking charger. · the wall power socket. Switch to standby The unit switches on automatically after power connection. · To switch the unit to standby mode, press on the back of the main speaker. · To switch the unit on from the standby mode, press again. · Connect the AC power cord to · the ~ AC IN socket on the back of the main speaker. · It takes about 35 seconds for the speakers to boot up. During boot-up, the LED indicator on the back of the main speaker blinks in green quickly. · After boot-up, the LED indicator starts to blink in green slowly. Prepare the remote control Caution · Risk of explosion!Keep batteries away from heat, · Perchlorate Material - special handling may apply. See www. dtsc. ca. gov/hazardouswaste/perchlorate. Never discard batteries in fire. EN 11 For first-time use: Remove the protective tab to activate the remote control battery. To replace the remote control battery: 1 1 2 3 Open the battery compartment. Insert one CR2032 battery with correct polarity (+/-) as indicated. Close the battery compartment. Note · Before pressing any function button on the remote · control, first select the correct source with the remote control instead of the main unit. If you are not going to use the remote control for a long time, remove the battery. 12 EN 4 Set up a WiFi network for AirPlay Note · Some operations may vary as you use different types of wireless routers. 3 Check the type of the wireless router you use. Connect speakers to a Wi-Fi network (router) Select a scenario below that matches your router type. Note · Each time when the speakers are powered on again, · the speakers enter the latest configured Wi-Fi network automatically. · Or open Safari on your PC/Mac, then select `Philips_Fidelio XXX' from the bonjour pull-down list. · Or open another web browser on your PC/Mac, then type in 192. 168. 1. 1 at the address bar. » The DS9800W configuration page is displayed. Network Configuration EN 15 3 4 Change the name of the SoundSphere speakers in Airplay Device Name if you like. [. . . ] Avoid using Wi-Fi channel which is using or much overlapped by the nearby Wi-Fi network. Keep away from potential sources of interference which may affect Wi-Fi signal, such as microwave ovens. If you fail to use your PC for Wi-Fi network setup, check whether your PC is using a Wi-Fi network. You cannot use Ethernet connection for AirPlay network setup. [. . . ]