User manual PHILIPS DTR2520

[. . . ] DTR 2520 User manual EN Unpacking the receiver As you unpack your terminal, make sure the following accessories are included: · 1 x remote control unit · 2 x AA batteries · 1 x mains cord with adapter for power supply · 1 x SCART cable · 1 x user manual · 1 x worldwide warranty booklet Plastic bags can be dangerous. To avoid suffocation keep the bag away from babies and children. Quick installation guide Refer to the safety section before connecting your receiver. 1 Disconnect your TV set and recorder from the mains. 2 Integrate your receiver in your existing installation as shown on the diagram. RF Cable Terrestrial Receiver to AC outlet TV set VCR/DVD PHILIPS EXT 2 EXT 1 EXT 1 EXT 2 ANT IN ANT OUT RF coaxial cables are not supplied. For comprehensive connection diagrams, see http://www. p4c. philips. com 2 3 Insert your smart card in your receiver with the golden or silver contacts facing up. [. . . ] For more information, refer to paragraph Timers Manager. - Press EXIT to save and exit. EN Setting a timer while watching digital TV or listening to digital radio - Press TIMER. - Scroll to a disabled timer to add a new timer and press OK. - Set the recording settings using the arrow or number keys as appropriate. For more information, refer to paragraph Timers Manager. - Press OK to confirm. Setting or modifying a timer from the Timers Manager - Scroll to the existing timer you want to modify or select a disabled timer to add a new timer. - Enable the timer by setting the Status to Enabled in case of a new timer. - Set the settings using the arrow or number keys as appropriate. For more information, refer to paragraph Timers Manager. - Press EXIT to save and exit. Deleting an active timer A timer is active as signalled by the front LED lit in dimmed green in TV or Radio mode or dimmed orange if your receiver is in standby. To delete the active timer: - If your receiver is in standby, press P+, P-, or any number key of the remote control. - Press the key sequence TIMER then 0. The LED is no longer dimmed and you can change channels. When a recording timer is active, you should not change digital channels or you will record the channel you tune to. However you can switch to analogue TV using the TV/STB key and zap through analogue channels. 19 EN Settings Menu Basic navigation While watching digital TV or listening to digital radio: - Press MENU to display the main menu. - Press t or y to scroll up or down to the menu item you want to select. - Press OK to display the corresponding sub items. - Press t or y to move to the desired sub item. Press BACK to go back one step in the menu, or EXIT to return to normal viewing. Changing settings Once you highlighted an adjustable item or sub item, you can then access the settings and make changes: - Use the u or i key to set an option or number keys to enter numerical values. - Press EXIT to save your changes and exit. To open a locked menu item, you need to enter your PIN-Code. Timers Manager Timers Manager is used to set and edit timers, including recording timers for the programmes you want to record using your VCR or DVD recorder To be able to record a digital channel using a VCR or DVD recorder, you must set both your recorder and receiver: - You must set a timer on your receiver. - You must also enable recording on the VCR or DVD recorder, either by enabling an Easy Record option or by programming your recorder (refer to chapter More about recording (VCR or DVD control) and to the VCR or DVD recorder user manual). 20 To add a timer, or modify or delete an existing timer: - Scroll to the existing timer you want to modify or delete, or to a disabled timer to add a new timer and then press OK. To add a timer, you may also press TIMER while watching digital TV or listening to digital radio, or press the appropriate colour key from the EPG. [. . . ] Make sure you are pointing your remote control at the receiver front panel. Check the batteries in your remote control. No sound or picture but the front panel LED is lit in green. Poor signal Receiver in TV mode Poor SCART connections The remote control does not operate your receiver. On-screen display working but there is no reception Intermittent reception The picture is not sharp and on-screen text is difficult to read. Poor reception/signal Check the installation. Faulty connections TV SCART output format not set to RGB Check all connections and cable. Change setting of the TV output signal item to RGB from the TV Configuration screen. 28 EN Problem Possible cause Action TV SCART not connected to the Refer to your TV User Manual. RGB capable SCART socket of your TV set Inappropriate TV SCART Use the SCART cable supplied with your receiver. [. . . ]