User manual PHILIPS DVD SHELF SYSTEM FWD5D37

[. . . ] · Your TV's Audio/Video In channel may be called AUX or AUXILIARY IN, AUDIO/VIDEO or A/V IN, EXT1 or External In, etc. , and may be near channel 00. Or, change TV channels until you see the blue Philips DVD background picture or the Initial Setup Screen on the TV. Using a Cable Box/Satellite Receiver 1. Connect the Cable TV or Satellite signal to the IN jack on your Cable Box or Satellite Receiver. Connect an RF coaxial cable to the OUT jack of the Cable Box/Satellite Receiver and to the ANTENNA jack on the rear of the DVD Recorder. [. . . ] Set the DVD Recorder to channel 3 or 4 (the output channel of your Cable Box/Satellite Receiver). Turn on the TV and set it to the correct Audio/Video In channel. You should see the Initial Setup menu on the TV screen the first time you turn on the DVD Recorder. EXT 2 EXT 1 Power cord to the DVD Recorder's MAINS jack and to a power outlet RIGHT AUDIO IN LEFT AUDIO IN VIDEO IN RIGHT AUDIO IN Audio and Video cables to the DVD Recorder's red and white AUDIO OUT (EXT 1/2) and yellow VIDEO OUT (CVBS) (EXT2) jacks and to the TV's AUDIO IN and VIDEO IN jacks LEFT AUDIO IN VIDEO IN EXT 3 COMPONENT VIDEO PROG SCAN Y L PB PB PB L EXT 3 Y Y L PR PR PR R R R IN RC 6 EXT 1/2 RF coaxial cable to the OUT jack of the Cable Box or Satellite Receiver and to the DVD Recorder's ANTENNA jack OUT IN Cable TV or Satellite signal to the IN jack on the Cable Box or Satellite Receiver 2 Set Up the Recorder Before you can use your new DVD Recorder to play Discs or make recordings, you must complete the Initial Setup. When you turn on the DVD Recorder for the first time, the menus shown at right will appear on the TV screen. TURN ON TV will appear on the DVD Recorder's display panel. Use the Arrow buttons and the OK button on the DVD Recorder's remote control to select items. Press SYSTEM MENU to clear the screen when TV channels are set. You will choose languages for different features, choose a TV Shape, and set up TV channels. This process will only take a couple of minutes, but you must complete it before you can use the DVD Recorder. You can not turn off the DVD Recorder or use any of the buttons on the DVD Recorder until you finish the Initial Setup. The only way to quit the Initial Setup is to disconnect the power cord. If you quit, the Initial Setup will appear again the next time you turn on the DVD Recorder. The menus will not go away until you finish the Initial Setup. Connect the DVD Recorder and TV as shown at right and on the first page of this Guide. Connect audio cables to the VCR's AUDIO Out jacks and to the red and white AUDIO In (CAM1/2) jacks on the front of the DVD Recorder. Connect a video cable to the VCR's VIDEO Out jack and to the yellow VIDEO In (CAM2) jack on the front of the DVD Recorder. (To access the DVD Recorder's front jacks, remove the protective cover by pulling the left side of the cover toward you. ) 3. Connect the power cords of all the equipment to a power outlet after you finish all other connections. Set the TV to the correct Audio/Video In channel. Stop play if necessary. Y Power cord to the DVD Recorder's MAINS jack and to a power outlet Antenna or Cable TV signal to the DVD Recorder's ANTENNA jack RIGHT AUDIO IN RIGHT AUDIO IN LEFT AUDIO IN VIDEO IN REAR OF TV Audio and Video cables to the DVD Recorder's red and white AUDIO OUT (EXT 1/2) and yellow VIDEO OUT (CVBS) (EXT2) jacks and to the TV's AUDIO and VIDEO IN jacks LEFT AUDIO IN VIDEO IN EXT 3 COMPONENT VIDEO PROG SCAN Y L PB PB PB L EXT 3 Y 5. Press OPEN/CLOSE A on the front of the DVD Recorder to open the disc tray. Insert a recordable DVD+RW or DVD+R with the label facing up. Press OPEN/CLOSE A to close the disc tray. Press 9 on the DVD Recorder's remote control to select an empty Title box in the Index Picture Screen on a DVD+RW. [. . . ] (To select a recording speed, press SELECT. ) 8. Press MONITOR on the DVD Recorder's remote. Press PLAY on the VCR to start tape playback. Press RECORD on the DVD Recorder to start recording. [. . . ]