User manual PHILIPS DVDR1000-051

[. . . ] Instructions for use General information Laser safety This unit employs a laser. To prevent possible eye injury, only a qualified service person should remove the cover or attempt to service this device. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄLASER ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄType 7ý7ý7ýSe ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄW ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄ7 ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄOutput Power 2 ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄ(out of o ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄ 7ý7ý0 ÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄÊÄB NEVER MAKE OR CHANGE CONNECTIONS WITH THE POWER SWITCHED ON. [. . . ] If you made a mistake, you can go back with t (left cursor). Programming with 'NEXTVIEW Link' This DVD recorder is equipped with the function 'NEXTVIEW Link'. If your television is also equipped with this function, you can mark TV programmes on the television for programming. These TV programmes will automatically be transmitted to a timer block on the DVD recorder. If you clear the marking of the TV programme on the television, the corresponding timer block on the DVD recorder will also be cleared. For more information, read the instruction manual of your TV set. If a timer setting is incorrect The following warnings can be displayed in the timer menu: Collision recording programme overlaps with another recording programme. The programme with the earlier start time will be recorded completely before the later programme starts. l Delete one of the recording programmes. Please enter programme number The VIDEO Plus+ system does not recognize the TV channel. Solution: l Select the required programme number (programme name) with t or u (left right cursor). PlusCode number wrong You entered an incorrect PlusCode number or the incorrect date. Solution: l Repeat the entry or end by pressing TIMER. Weekend programming - not possible Date was incorrectly entered. Daily programming can only be used for recordings to be made from Mondays to Fridays inclusive. Memory full The maximum number of recording programmes is used. Solution: l Delete one of the recording programmes. Timer Timer programming Date 09 Prog. Start NED 1 09:35 VPS PDC End 11:35 Rec Mode SP * Mo Fr Weekly Press SELECT To store Press OK l l l Confirm with OK . The data has been stored in a timer block. Make sure that you inserted a disc without write protection. If you inserted a write-protected (locked) disc, recording will be refused. Switch off with B STANDBY/ON. RECORDING 35 English English l How to check or alter a timer block l Press TIMER on the remote control. Select `Timer list' with w or v (down up cursor). How to clear a timer block Timer CLEAR TIMER SELECT VIDEO Plus+ programming Timer programming Timer list l l l l l To exit Press TIMER l l Press TIMER on the remote control. Select `Timer list' with w or v (down up cursor). [. . . ] `VideoPlus+' is a trademark of Gemstar Development Group. Video Programming System SCART SECAM ShowView S-video Title TruSurround TV system VCD VCR VIDEO Plus+ VPS 54 GLOSSARY Appendix Using your DVD recorder remote control with your TV set Your DVD recorder remote control can transmit several commands to TV sets of different brands. The following keys will always operate the TV set: CLEAR TIMER SELECT a P MUTE If your TV set does not respond to the remote control, you can re-programme your remote control. Below you will find a list of all available remote control codes for various TV brands. [. . . ]