User manual PHILIPS FW-C55

[. . . ] FW- C55 with 3 CD changer Mini Hi-Fi System 1 pg 01-26/C55/22-Eng new 1 3/6/00, 11:42 AM 3139 116 19311 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] TM The display will show "SEARCH" until a radio station with sufficient signal strength is found. 16 · Repeat this procedure until the desired station is reached. · To tune to a weak station, briefly press à or á repeatedly until the display shows the desired frequency and/or when the best reception has been obtained. Manual programming 1 Press TUNER (BAND). 2 Press TUNER (BAND) again to select the desired waveband : FM, MW or LW. TM The next available preset number will be displayed for selection. 4 Press à or á to tune to the desired frequency. · If you wish to store the radio station to another preset number, press 4 or 3 to select the desired preset number. TM The PROGRAM disappears and the radio station will be stored. · Repeat steps 3 ­ 5 to store other preset radio stations. pg 01-26/C55/22-Eng new 16 v English Notes: ­ You can cancel the automatic programming by pressing PROG orÇ (on the system only). ­ If you want to reserve a section of preset numbers, for example preset numbers 1 to 9, select preset 10 before starting automatic programming, only the preset numbers 10 to 40 will be programmed. Notes: ­ When 40 radio stations are stored and you attempt to store another radio station, the display will show "FULL". If you want to change an existing preset number, repeat steps 3 ­ 5. ­ You can cancel manual programming by pressing Ç (on the system only). ­ During programming, if no button is pressed within 20 seconds, the system will exit program mode automatically. 3/6/00, 11:43 AM 3139 116 19551 TUNER Tuning to Preset Radio Stations · Press 4 or 3 to select the desired preset number. TM The preset number, radio frequency, and waveband appear on the display. Receiving RDS Radio Station Ç RDS (Radio Data System) is a broadcasting service that allows FM stations to send additional information along with the regular FM radio signal. This additional information can contain: · STATION NAME: The radio station name is displayed. · PROGRAM TYPE: The following program types exist and can be received by your tuner: News, Affairs, Info, Sport, Educate, Drama, Culture, Science, Varied, Pop M, Rock M, M. O. R. (middle of the road music), Light M, Classics, Other M, No type. · RADIO TEXT (RT): text messages appear in the display. When you have tuned to a RDS station, the RDS logo (Ç) and the radio station name will appear on the display: · The display normally shows the radio station name if available. By repeatedly pressing RDS button you can change the type of display information: TM The display shows in turn: STATION NAME TM PROGRAM TYPE TM RADIO TEXT TM TUNED FREQUENCY TM STATION NAME . . . Note: ­ When you press the RDS button and the display shows "NO RDS", it indicates that either the tuned station is not transmitting RDS signal or it is a non RDS station. RDS Clock Some RDS station may be transmitting a real clock time at an interval of every minute. Setting the time with RDS clock 1 Press CLOCK/TIMER. TM "--:--" or current time appears on the display. 2 Press CLOCK/TIMER once more to enter clock setting mode. [. . . ] · Magnetic build-up in the record/ playback head. · Power failure or AC power plug disconnect from the wall outlet during tape playback. TM Reconnect the AC power plug and switch on the system again. General System does not react when any button is pressed. TM Press STANDBY ON to switch the system off. [. . . ]