User manual PHILIPS FW-C90

[. . . ] FW- C90 with 3 CD changer Mini Hi-Fi System pg 01-29/C90/22-Eng 1 3/6/00, 1:52 PM 3139 116 19701 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] TM The REPEAT, PROGRAM and SHUFFLE appear on the display. 17 pg 01-29/C90/22-Eng 17 3/6/00, 1:53 PM 3139 116 19701 English Playing the program Erasing the program (when 2 Press SHUFFLE again to resume normal playback. TM The SHUFFLE disappears from the display. TUNER MINI HIFI SYSTEM STANDBY ON DOLBY B NR NEWS/TA POWER SAVE RDS IR SENSOR CD 1·2·3 C1 · 2 · 3 CD VEC BASS/ T BAND BAND TUNER STOP·CLEAR TAPE 1·2 TAPE PLAY PAUSE v CDR/DVD CDR AUX PRESET v PREV SIDE NEXT CD TEXT RE SEARCH·TUNING BL VOLUME PERSON AL DS C E PROG CLOCK/ TIMER DIM A. REV DUB (HSD) RECORD DYNAMIC BASS BOOST BASS TREBLE TM The system will start searching for all radio stations with RDS and then followed by radio stations on FM, MW and LW band respectively. TM All available stations will be stored automatically. The frequency and preset number will be displayed briefly. TM The system will stop searching when all the available radio stations are stored or when the memory for 40 preset radio stations is used. TM The system will remain tuned to the last stored preset radio station. 4 Press à or á to tune to the desired frequency. · If you wish to store the radio station to another preset number, press 4 or 3 (or Digit 0-9 on the remote control) to select the desired preset number. TM The PROGRAM disappears and the radio station will be stored. · Repeat steps 3 ­ 5 to store other preset radio stations. English 18 Note: ­ For 'EASY SET' feature, please refer to page 11. Tuning to radio stations 1 Press TUNER (BAND) to select TUNER mode. A few seconds later, the current radio frequency will be displayed. 2 Press TUNER (BAND) again to select the desired waveband : FM, MW or LW. 3 Press à or á for more than one second, then release. TM The display will show "SEARCH" until a radio station with sufficient signal strength is found. · Repeat this procedure until the desired station is reached. · To tune to a weak station, briefly press à or á repeatedly until the display shows the desired frequency and/or when the best reception has been obtained. Storing Preset Stations You can store up to 40 radio stations in the memory. When a preset radio station is selected, the preset number appears next to the frequency on the display. Automatic programming 1 Press TUNER (BAND). TM The PROGRAM starts flashing and "AUTO" will be displayed. Notes: ­ You can cancel the automatic programming by pressing PROG orÇ (on the system only). ­ If you want to reserve a section of preset numbers, for example preset numbers 1 to 9, select preset 10 before starting automatic programming, only the preset numbers 10 to 40 will be programmed. Manual programming 1 Press TUNER (BAND). 2 Press TUNER (BAND) again to select the desired waveband : FM, MW or LW. TM The next available preset number will be displayed for selection. Notes: ­ When 40 radio stations are stored and you attempt to store another radio station, the display will show "PROGRAM FULL". If you want to change an existing preset number, repeat steps 3 ­ 5. [. . . ] TM Reconnect the AC power plug and switch on the system again. System does not react when any button is pressed. TM Press STANDBY ON to switch the system off. Remove the AC power plug from the wall outlet, then reconnect the power plug and switch on the system again. [. . . ]