User manual PHILIPS FW-M55

[. . . ] FW- M55 with 3 CD changer Mini Hi-Fi System FWM55-22-GB-ENG-V01 1 12/8/00, 1:57 PM 3139 115 20071 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] TM The display will show "SEARCH" until a radio station with sufficient signal strength is found. 16 · Repeat this procedure until the desired station is reached. · To tune to a weak station, briefly press à or á repeatedly until the display shows the desired frequency and/or when the best reception has been obtained. Manual programming 1 Press TUNER (BAND). 2 Press TUNER (BAND) again to select the desired waveband : FM, MW or LW. TM The next available preset number will be displayed for selection. 4 Press à or á to tune to the desired frequency. · If you wish to store the radio station to another preset number, press 4 or 3 to select the desired preset number. TM The PROGRAM disappears and the radio station will be stored. · Repeat steps 3 ­ 5 to store other preset radio stations. FWM55-22-GB-ENG-V01 16 v English Notes: ­ You can cancel the automatic programming by pressing PROG orÇ (on the system only). ­ If you want to reserve a section of preset numbers, for example preset numbers 1 to 9, select preset 10 before starting automatic programming, only the preset numbers 10 to 40 will be programmed. Notes: ­ When 40 radio stations are stored and you attempt to store another radio station, the display will show "FULL". If you want to change an existing preset number, repeat steps 3 ­ 5. ­ You can cancel manual programming by pressing Ç (on the system only). ­ During programming, if no button is pressed within 20 seconds, the system will exit program mode automatically. 12/8/00, 1:57 PM 3139 115 20071 TUNER Tuning to Preset Radio Stations · Press 4 or 3 to select the desired preset number. TM The preset number, radio frequency, and waveband appear on the display. Receiving RDS Radio Station Ç RDS (Radio Data System) is a broadcasting service that allows FM stations to send additional information along with the regular FM radio signal. This additional information can contain: · STATION NAME: The radio station name is displayed. · PROGRAM TYPE: The following program types exist and can be received by your tuner: News, Affairs, Info, Sport, Educate, Drama, Culture, Science, Varied, Pop M, Rock M, M. O. R. (middle of the road music), Light M, Classics, Other M, No type. · RADIO TEXT (RT): text messages appear in the display. When you have tuned to a RDS station, the RDS logo (Ç) and the radio station name will appear on the display: · The display normally shows the radio station name if available. By repeatedly pressing RDS button you can change the type of display information: TM The display shows in turn: STATION NAME TM PROGRAM TYPE TM RADIO TEXT TM TUNED FREQUENCY TM STATION NAME . . . Note: ­ When you press the RDS button and the display shows "NO RDS", it indicates that either the tuned station is not transmitting RDS signal or it is a non RDS station. RDS Clock Some RDS station may be transmitting a real clock time at an interval of every minute. Setting the time with RDS clock 1 Press CLOCK/TIMER. TM "--:--" or current time appears on the display. 2 Press CLOCK/TIMER once more to enter clock setting mode. [. . . ] TM Press STANDBY ON to switch the system off. Remove the AC power plug from the wall outlet, then reconnect the power plug and switch on the system again. · Speakers are not connected or are connected wrongly. TM Check that the speakers are connected correctly. [. . . ]