User manual PHILIPS FW-V220-21M

[. . . ] This is an important parameter for CD players other than CD Audio, and especially for the Video CD applications, because any loss of data from the disc will at best cause disturbances in the reproduced picture, and at worst can cause the player to lose track so that disc playing fails. Presenting Super Error Correction To ensure consistently good results when playing Video CD discs of all quality grades and conditions, Philips has introduced further improvements in the system's playability. These developments together are called Super Error Correction, a proprietary Philips technology optimizing the system's ability to handle lessthan-perfect discs with the minimum disturbance to normal playing. By effectively eliminating virtually all errors arising under normal playing conditions, Super Error Correction ensures that the picture quality as seen by the user is independent of disc play. The video encoding and processing during mastering of the disc, and the MPEG-1 decoding and video encoding in the signal processing stages, are now the only limiting factors for picture quality. 2 12/11/01, 5:05 PM 3139 pg 001-032/V520/21-Eng 2 115 21093 4 3 2 1 £ TM ¡ ) ( * % & FWSTANDBY-ON 3 DISC DIRECT PLAY DISC CHANGE 5 DISC 3 OPEN· CLOSE DISC 1 DISC 2 6 7 8 VOLUME 3VCD CHANGER CD / CD-R / CD-RW COMPATIBLE CD SYNCHRO RECORDING VCD MINI HIFI SYSTEM INTERACTIVE VU METER TITLE/ ALBUM NAME MP3-CD DISPLAY PROG CLOCK· AUTO TIMER REPLAY DUBBING REC VIGATION D NA - JO UN G SO PBC CD 1·2·3 PRESET EV TITLE N BAND DS C MAX SOUND RETURN INCREDIBLE SURROUND VCD PAL/ NTSC TUNER DEMO STOP/ CLEAR S PLAY· PAUSE SOURCE G 9 0 ! [. . . ] For Recording, please refer to "Tape Operation/Recording". 1 Press REPEAT on the remote control repeatedly to select various repeat modes. G In normal playback "REPEAT TRACK" ­ to repeat the current track. "REPEAT DISC" ­ to repeat the entire disc. G In programme playback "REPEAT TRACK" ­ to repeat the current programmed track. "REPEAT PROGRAM" ­ to repeat all programmed tracks. RPT and PROG will appear on the display. G The current track/disc/programme will now be played repeatedly until you press Ç. 2 To resume normal playback, press REPEAT until the "REPEAT OFF" mode is displayed. RPT will disappear from the display. 19 12/11/01, 5:05 PM 3139 pg 001-032/V520/21-Eng 19 115 21093 English Title/Album Name CD/VCD/MP3-CD Operation VIDEO CD OSD ­ On Screen Display If you insert VCD, your TV screen will serve as an additional display for messages (e. g. PLAY, STOP), and information stored on the VCD. English OSD 2 AUX TUNER TAPE 1/2 G Press OSD on the remote control repeatedly to switch on or off the On Screen Display. When OSD is switched ON; you can see the following display on the TV screen. Notes: ­ You can also cancel A-B Repeat by pressingí orë. ­ You can only able to set the A-B marking within the same track. Once it crosses from one track to the next, the A-B marking is reset. Digest This feature allows you to scan through a VCD for a quick review. There are four digest mode for selection. 1 1 Press DIGEST on the remote control. "DIGEST" appears on the display. "1. INTRO SCAN" , "2. DIGEST DISC" , "3. DIGEST TRACK" and "4. EXIT DIGEST MENU" appear on the TV screen. 1. EXIT DIGEST MENU G Press digit 1 on the remote control to select "INTRO SCAN". The first 10 seconds of each track are played. G Press digit 2 on the remote control to select "DIGEST DISC". The first frame of each track appears on the TV screen. Press digit 0 ­ 9 on the remote control to playback the desired tracks. [. . . ] If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Problem DISC PLAYER OPERATION "UNREADABLE DISC" is displayed. Solution ­ Check if the disc is inserted upside down. ­ Wait until the moisture condensation at the lens has cleared. ­ Replace or clean the disc, see "Maintenance". [. . . ]