User manual PHILIPS HD8824/01

[. . . ] Super automatic espresso machine 3000 series 02 USER MANUAL Read carefully before using the machine. HD8824 HD8825 02 EN Register your product and get support at www. philips. com/welcome English IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. Close supervision is necessary when the appliance is used by or near children. Unplug from outlet when not in use and before cleaning. [. . . ] You will taste the difference after brewing 2-3 cups of coffee. 3 The reference marks inside the coffee bean hopper indicate the grind setting. There are 5 different grind settings to choose from, from position 1 ( ) for coarse grind - lighter taste to position 2 ( ) for fine grind stronger taste. If coffee is watery or is brewed slowly, change the coffee grinder settings. 1 2 Adjusting the Coffee Dispensing Spout The height of the coffee dispensing spout can be adjusted to better fit the dimensions of the cups that you wish to use. Move the coffee dispensing spout up or down with your fingers to adjust its height as shown in the figure. ENGLISH 21 The recommended positions are: For the use of small cups; For the use of large cups. Two cups can also be placed under the coffee dispensing spout to brew two cups of coffee or two cups of espresso at the same time. 22 ENGLISH Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups. Each time the “ ” or “ ” button is pressed, the machine brews a pre-set amount of coffee. Each button may be individually programmed for a specific brew setting. The following procedure describes how to program the “ ” button. 1 Place a cup under the coffee dispensing spout. 2 Press and hold the “ ” button until it starts to flash quickly. The “ ” button flashes throughout the programming cycle. The machine starts brewing coffee. 3 Press the “ reached. ” button as soon as the desired amount of coffee is Now the button “ ” is programmed; each time it is pressed, the machine will brew the same amount of espresso that was just programmed. Note: Follow the same procedure to program the “ ” button. Press the “ ” button to stop brewing when the desired amount of coffee is reached. ENGLISH 23 BREWING ESPRESSO AND COFFEE Before brewing coffee, make sure that there are no warnings shown on the control panel, and that the water tank and coffee bean hopper are filled. The " ", " ", " " and " " buttons are shining steadily. 1 Place 1 or 2 cups under the coffee dispensing spout. 2 Press the “ ” button for an espresso or the “ ” button for a coffee. 3 To brew 1 cup of espresso or coffee, press the desired button once. The pressed button flashes slowly. 4 To brew 2 cups of espresso or coffee, press the desired button twice consecutively. The pressed button flashes quickly twice. Note: In this operating mode, the machine automatically grinds and doses the correct amount of coffee. Brewing two cups of espresso or coffee requires two grinding and brewing cycles, automatically carried out by the machine. 5 After the prebrewing cycle, coffee begins to pour out of the coffee dispensing spout. 6 Coffee brewing automatically stops when the preset level is reached; press the same button pressed previously to stop it earlier. 24 ENGLISH FROTHING MILK / BREWING CAPPUCCINO Frothing milk Warning: Danger of scalding!Dispensing may be preceded by small jets of hot water. When steam is used, the steam wand and the chrome cover may reach high temperatures. The Automatic Milk Frother must be handled only by using its knurled plastic handle. 1 Fill 1/3 of a container with cold milk. Note: When preparing your cappuccino, use cold (~5°C / 41°F) milk with a protein content of at least 3% to ensure optimum results. Whole milk or low-fat milk can be used depending on your personal taste. Note: When you plan to froth milk right after switching on the machine or after brewing a coffee, some water still present in the circuit may need to be dispensed first. To do this, press the “ ” button to dispense steam for a few seconds. Thereafter press the “ ” button to stop dispensing. Then proceed with step 2. 2 Before frothing milk, make sure that the machine is ready to use and the water tank is filled. ", " ", " " and " " buttons are shin- ENGLISH 25 3 Insert the suction tube into the Automatic Milk Frother. 4 Insert the Automatic Milk Frother into the steam wand seat. Note: Make sure that it is positioned correctly. [. . . ] Clean the coffee dispensing spout and its holes. Clean the hole of the steam wand using a pin. Make sure that the machine is off and has cooled down before performing this operation. Press the ON/OFF button and follow the instructions described in the “Interruption of the Descaling Cycle” chapter. Machine actions The machine grinds the coffee beans but no coffee is brewed (see note). The circuit is not primed. [. . . ]