User manual PHILIPS HD 8838

[. . . ] 02 MACHINE DISPOSAL - The packing materials can be recycled. - Appliance: Unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service center or public waste disposal facility. This product complies with eu directive 2002/96/ec. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ] Make sure the container is inserted up to its limit. Green HOT MILK BREWING Danger of scalding!Brewing may be preceded by small jets of hot water. After filling the milk container, place it in the machine. Make sure the container is inserted up to its limit. Press the “ ” button until the following page is displayed. Green Place the cup you use every day to enjoy your hot milk. Press the “ hot milk. ” button to start brewing • 12 • Press the “ “ button. Each brewing phase is programmed, but can be interrupted in advance by pressing the “ ” button. • Once milk has been brewed, the machine brews the coffee. Green • The following icon is displayed during the preheating time required by the machine: Orange In this phase the machine starts grinding coffee and/or gets ready to brew coffee. • When the following icon is displayed, the machine brews frothed milk directly in the cup. Orange Important note: Immediately after using the machine to brew a cappuccino, clean all components as described in the "Cleaning of the Milk Brewing System" section. Green The icon on the side is displayed during the short warm-up phase required by the machine. Orange Orange Important note: Immediately after using the machine to brew a hot milk, clean all components as described in the "Cleaning of the Milk Brewing System" section. Once the ideal temperature is reached, the machine begins brewing the programmed amount of hot milk. Green Brewing will stop automatically. If you wish to interrupt hot milk brewing, press the “ ” button. • 13 • Milk, even UHT milk, goes bad easily at room temperature; therefore, it is recommended to DO NOT keep it at room temperature for long periods. Furthermore, the milk carafe has always to be put back in the fridge when it is not needed. It is also advisable to keep the parts in contact with the milk cleaned following the directions and recommendations described in these instructions. AUTOMATIC CLEANING FUNCTIONS Before entering the Stand-by mode, the machine automatically performs a short cleaning cycle in the milk brewing area. Moreover, after brewing any kind of milk-based beverage, the machine reminds the user to clean the parts that have been in contact with the milk. This warning does not block any function of the machine and can be deleted by pressing the right lower button every time it appears. Orange However, it is advisable to regularly clean the parts of the machine in contact with the milk following the instructions described in the "CLEANING OF THE MILK BREWING SYSTEM" section of the manual. FAST CLEANING (It is recommended to perform it after each milk brewing) Before performing this operation remove the milk carafe from the machine. Orange • 14 • After having brewed milk for some times, turn the main knob to the right as for hot water dispensing: the image "CLEAN+” will appear. Place a container under the dispensing spout and push the upper link button to start the cleaning operation. Then, bring the knob back to the central position to allow other brewing programmes. C L E A N I N G O F PERIODIC CLEANING (It is recommended to perform this cleaning every time the milk carafe is removed, when the milk system does not work properly or has milk deposits on it). It is recommended to regularly clean the parts for brewing and frothing milk by dismounting both the parts installed on the machine and those installed on the carafe. Dismount the parts installed on the machine according to the instructions showed in the following figures: T H E M I L K B R E W I N G S Y S T E M • 15 • PERIODIC CLEANING Proceed as follows for the parts installed on the carafe. • Remove the carafe from the machine. • Lift the cover and pay attention that the wand does not splash the remaining milk. • Remove the wand from the cover. • Remove the pin: - Rotate it counter-clockwise. - Take off the pin from the cover. • Wash the cover and the carafe with lukewarm water. • Wash the wand and the pin of the machine by running lukewarm water inside the duct. • After rinsing and drying all components, assemble the pin on the cover: - Place the pin into the cover. Insert the wand in the cover FROM THE STRAIGHT-CUT END and place the cover over the milk container. These parts can also be washed in the dishwasher placing them in the cutlery basket so that they do not get lost. [. . . ] 1. 2 litres – Removable Coffee Bean Hopper Capacity (g). Thermal fuse • 30 • TROUBLESHOOTING Machine Actions The machine does not turn on. The coffee is not hot enough No hot water or cappuccino comes out. Causes Solutions The coffee has not enough crema. (See note) The machine takes a long time to warm up or the amount of water dispensed from the wand is too little. [. . . ]