User manual PHILIPS LC1041

[. . . ] User guide ProScreen PXG10 multimedia projector ) Menu Menu D-Zoom c Auto syn OK Lens Input te A/V Mu Philips Creative Display Solutions IMPORTANT NOTE FOR USERS IN THE U. S. A. The responsible party of this multi media projector is the following: Philips Consumer Electronics Company One Philips Drive Knoxville, TN 37914 Telephone (1888) 873-4672 English WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. [. . . ] To use the 5 BNC connector, slide the 15 pin/BNC switch (M) on the rear terminals to the BNC position. Connect each BNC connector to the corresponding BNC Input 1 terminals (E) on the projector. (BNC-RCA adapters (6) are included for use with RCA type cables and sources. ) 2. Connect the other end of the cable (2) to the corresponding terminals of a DVD player or DTV decoder. To use the built-in audio system, connect one end of the computer audio cable (optional) to Audio Input 1 terminal (B) on the projector. Connect the other end to the Audio output terminal on the video source. When connecting the projector to a DVD player or a DTV decoder equipped with Component video outputs, select "Component" for "Signal Type" in the GUI "Options" menu (see page 23). Note: After the use of "Component" when connecting to a computer , again, select "Computer/RGB" for "Signal Type" in the GUI menu (see page 23). 7. INSTALLATION Connecting to audio equipment/remote control mouse receiver General ­ The figures in brackets (1) correspond to the figures in the diagram on page 10. ­ The characters in brackets (A) correspond to characters in fig. CONNECTING TO AUDIO EQUIPMENT CONNECTING THE REMOTE CONTROL MOUSE RECEIVER When the RS-232C port on the projector is connected to a computer with an RS-232C cable (cross type, sold separately), the computer can be used to control the projector and check the status of the projector. Always turn off the projector while connecting to audio components, in order to protect both the projector and the components being connected. By using external audio components, the volume can be amplified for better sound. Computer - RGB / Component inputs Data 1 in (15pin) Audio 1 Data 2 in Audio 2 Data 1 in (BNC) 15pin BNC R (Pr) G/G sync (Y) B (Pb) HD (C sync) VD APPARATEN SKALL ANSLUTAS TILL JODAT UTTAG. Audio in LR Video in Data out Audio out (G) 110-120V / 220-240V~ RS-232C S-Video in Optional Computer Data out Mouse Audio out USB L Audio R in · Connect the Audio in L/R sockets of an amplifier or stereo system to the Audio out socket (G) of the projector. For this, use an audio connection cable (optional). (8) · Connect the supplied USB mouse receiver to the corresponding USB terminal on the PC. CAUTION!­ The minimum system requirements for the USB mouse receiver are Windows 98 and/or Windows NT 5. 0 or higher. 13 English CONNECTING TO AUDIO EQUIPMENT/THE REMOTE CONTROL MOUSE RECEIVER 8. OPERATION PREPARATION Turning on/off the power 1. Make the necessary connections before proceeding. Connect the power cord to a wall outlet. The Power indicator lights up red and the projector enters standby mode. Preparation Men u Volu me AV-M ute Vide o A-Mu te Data 2 Data 1 D1 D2 DATA DATA ­ When no signal is being received, "NO SIGNAL will be " displayed. When a signal that the projector is not preset to receive is being received, "NOT REG. (on the local keyboard only) 30° 4m (13'8) 30° 45° Using the remote control in a dark room · Press BACKLIGHT, and the buttons will light up. 5. Press A/V Mute to temporarily turn off the sound and picture. Notes: ­ Be sure the supplied USB mouse receiver is connected to your computer. ­ The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer's operation manual for details of setting up/installing the mouse driver. [. . . ] ­ `Lamp 0000H' is displayed, indicating that the lamp timer is reset. Maintenance KENSINGTON LOCK This projector has a Kensington Security Standard slot for use with a Kensington Micro Saver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector. Kensington Security Standard connector ) 27 English 10. TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the projector for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service organisation. English PROBLEM · CHECK · · · · 28 WARNING Under no circumstances should you try to repair the projector yourself as this could invalidate the warranty. NO PICTURE AND NO SOUND. [. . . ]