User manual PHILIPS LC1241

[. . . ] User guide ProScreen PXG20 Multimedia projector ) Menu Menu D-Zoom c Auto syn OK Input te A/V Mu Lens Philips Creative Display Solutions IMPORTANT NOTE FOR USERS IN THE U. S. A. The responsible party of this multi media projector is the following: Philips Consumer Electronics Company One Philips Drive Knoxville, TN 37914 Telephone (1888) 873-4672 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. [. . . ] INSTALLATION Connecting to audio equipment/remote control mouse receiver CONNECTING TO AUDIO EQUIPMENT/THE REMOTE CONTROL MOUSE RECEIVER General ­ The figures in brackets (1) correspond to the figures in the diagram on page 11. ­ The characters in brackets (A) correspond to characters in fig. CONNECTING TO AUDIO EQUIPMENT CONNECTING THE REMOTE CONTROL MOUSE RECEIVER When the RS-232C port on the projector is connected to a computer with an RS-232C cable (cross type, sold separately), the computer can be used to control the projector and check the status of the projector. CAUTION!Always turn off the projector while connecting to audio components, in order to protect both the projector and the components being connected. By using external audio components, the volume can be amplified for better sound. Computer - RGB / Component inputs Data 1 in (15pin) Audio 1 Data 2 in Audio 2 Data 1 in (BNC) 15pin BNC R (Pr) G/G sync (Y) B (Pb) HD (C sync) VD APPARATEN SKALL ANSLUTAS TILL JODAT UTTAG. Audio in LR Video in Data out Audio out (G) 110-120V / 220-240V~ RS-232C S-Video in Optional Computer Data out Mouse Audio out USB L Audio R in · Connect the Audio in L/R sockets of an amplifier or stereo system to the Audio out socket (G) of the projector. For this, use an audio connection cable (optional). (8) · Connect the supplied USB mouse receiver to the corresponding USB terminal on the PC. CAUTION!­ The minimum system requirements for the USB mouse receiver are Windows 98 and/or Windows 2000 or higher. 14 8. OPERATION Preparation PREPARATION Turning on/off the power 1. Make the necessary connections before proceeding. The Power indicator lights up red and the projector enters standby mode. 2. The power indicator lights up green and the flashing green Lamp indicator shows that the lamp is warming up. Wait until the indicator stops flashing before operating the projector. If the power is turned off and then immediately turned on again, it may take a short while before the lamp turns on. Notes: ­ If the bottom filter cover is not securely installed, the Power indicator flashes in red. ­ After the projector is unpacked and turned on for the first time, a slight odour may be emitted from the exhaust vent. This odour will soon disappear with use. Notes: ­ Wait until the cooling fan stops (about 2 minutes after the projector has been switched off) before disconnecting the powercord. ­ The power can be turned on again by pressing Power ON. When the power is turned on, the Power indicator and the Lamp indicator light green. USING THE REMOTE CONTROL (fig. 2) The remote control has the following two functions: · Projector control · Wireless mouse · Slide the remote control power ON/OFF switch into the ON position for switching the projector and the Remote Control unit to on. ­ The remote control can be used to control the projector within the ranges shown below. ­ The USB mouse receiver can be used with the remote control to control the mouse functions of a connected computer within the ranges shown below. 7m (23'8) D1 Remarks: 1) When the power is on, the Lamp indicator (Lamp) indicates the status of the lamp. 2) After the picture is displaying, the warming-up indicator `WARMING UP, PLEASE WAIT' is shown 3. Press the button of the desired input mode, Data 1, Data 2, Video. [. . . ] ­ Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of the projector. KENSINGTON LOCK This projector has a Kensington Security Standard slot for use with a Kensington Micro Saver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector. Kensington Security Standard connector ) 31 12. TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the projector for repair. [. . . ]