User manual PHILIPS LC4433

[. . . ] Philips multimedia projector cSmart Series User guide English Menu OK AV te Mu e Volum Stand by p Lam RC Keysto ne 0. Controls and connections 1 2 3 4 AV te Mu Menu OK 5 6 7 8 9 AV Mute Source Keystone Lamp Stand by RC @ $ fig. 1 a b c d e f g h Audio out USB Video audio-in Data audio-in Video S-Video Data out Data in l k j i 1 2 3 4 Stand by On Left Mouse MOUSE Volume VOLUME Right Menu MENU OK !0 5 6 7 Mute MUTE AV Mute AV MUTE Source SOURCE D-Freeze D-FREEZE D-Zoom D-ZOOM 9 8 AV MUTE fig. [. . . ] · Check that the projector receives the signals from the remote control (LED ring around the Standby button will fast flash when receiving a signal). If no audio information is heard via the projector speaker: · Check (AV) Mute setting. · Check Volume setting. You can also make an Audio out connection to an external amplifier. See `Connecting to audio equipment'. 11 7. Installation Connecting to video equipment Connecting to video equipment Note: The figures in brackets (1) correspond to the figures in the accessories diagram. The characters in brackets (a) correspond to the characters in fig. Always switch off the projector before making any connections. PAL, NTSC, SECAM (c) (e) S-VHS (c) (f) Audio out USB Video audio-in Data audio-in Video video Data S-Video Data out Data Audio out USB Video audio-in Data audio-in video Data Video S-Video Data out Data in Projector (2) (4) (3) S-Video Projector (2) VCR R Audio L out Video out S-Video R (3) Scart adapter (not for USA version) VCR L Audio R out Video out Scart adapter (not for USA version) 1. Connect the S-Video out socket of a S-VHS video recorder, Laser Disc player, video camera or TV to the S-Video socket (f) of the projector. For this use the S-Video connection cable (4) supplied. Connect the Audio out L/R sockets of the S-VHS video recorder, Laser Disc player, video camera or TV to the Video audio-in socket (c) of the projector. In case your VCR, Laser Disc player, video camera or TV is equipped with a Scart connector (depending on region): 1. Connect the Scart/RCA Audio Video adapter (3) supplied to the Scart connector of the VCR, Laser Disc player, video camera or TV. Plug the audio/video connection cable (2) supplied into both the adapter and Video audio-in socket (c) of the projector. Plug the S-Video connection cable supplied into the VCR and the S-Video socket (f) of the projector. 1. Connect the Video out socket of a VCR, Laser Disc player, video camera or TV to the Video socket (e) of the projector. For this, use the video/audio connection cable (2) supplied. Connect the Audio out L/R sockets of the VCR, Laser Disc player, video camera or TV to the Video audio-in socket (c) of the projector. For this, use audio/video connection cable (2) supplied. In case your VCR, Laser Disc player, video camera or TV is equipped with a Scart connector (depending on region): 1. Connect the Scart/RCA Audio Video adapter (3) supplied to the Scart connector of the VCR, Laser Disc player, video camera or TV. Plug the video/audio connection cable (2) supplied into both the adapter and the Video (e) and Video audio-in (c) sockets of the projector. 12 7. Installation - Connecting to Component video equipment Connecting to Component video equipment Note: The characters in brackets (a) correspond to characters in fig. [. . . ] ­ red (fast blinking): lamp start has failed. · Disconnect projector from the mains. If this does not resolve the problem, replace the lamp. ­ slow blinking (green, red or orange): lamp is starting up or cooling down. [. . . ]