User manual PHILIPS LTC2375

[. . . ] LTC 2372, LTC 2375 LTC 2376, LTC 2377 VidQuad® Digital Processor Units Eng Installation Instructions F D E NL I IMPORTANT SAFEGUARDS 1. 7. 8. 9. 10. 11. 12. 13. 14. 15. Read Instructions - All the safety and operating instructions should be read before the unit is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. [. . . ] The n Press the and keys to establish the necessary digit. (Calenders until the year of 2097 are in this menu. ) Press the key. n n 5. 3. 4 Display Mode Set Select the DISPLAY function. (1) (2) (3) (4) (5) TIME FORMAT DATE FORMAT TIME/DATE SET DISPLAY : BOTTOM EXIT n Press the 1 key, and toggle to select the required format. Options are: 12 HOURS (AM/PM) 24 HOURS (0000-2359). Press the key. n n n 5. 3. 2 Date Format Select DATE FORMAT and press the following menu is displayed: DATE FORMAT MM/DD/YEAR Press the key to toggle through BOTTOM, TOP, and OFF. The Date/Time will be displayed on the monitor in the selected position. Select EXIT and press the key to exit the menu. key. The n 5. 4 Camera Sequence Setup This menu allows you to adjust the dwell times of the 4 camera video and the Quad screens. The following menu is displayed: DWELL TIME > > n Press the 1 key, and toggle to select the required format. Options are: MM/DD/YEAR DD/MM/YEAR YEAR/MM/DD (1) (2) (3) (4) (5) (6) CAMERA 1 : 9 SEC CAMERA 2 : 9 SEC CAMERA 3 : SKIP CAMERA 4 : 9 SEC QUAD : 9 SEC EXIT n Press the key. n Press the channel. and keys to move the cursor to required > 1. 8 n Press the key to increase the dwell time. Dwell times may be programmed from SKIP to 9 seconds. (When you reach 9 seconds, pressing the key will toggle you through the sequence again. A setting of "SKIP" removes the channel from the sequence. Select EXIT and press the key to exit the menu. 5. 5. 2 Alarm Dwell Time The ALARM DWELL function allows you to set the automatic reset period after an alarm is generated. n Select ALARM DWELL and press the following menu is displayed: AUTO RESET TIME key. The n 5. 5 Alarm Setup The ALARM SETUP menu allows you to set the alarm options for each of the video inputs. The alarms can be set on or off, dwell time, polarity and video loss. The unit can also have the audio beeper set to on or off. n 60 SEC Select ALARM SETUP and press the following menu is displayed: ALARM SETUP (1) (2) (3) (4) (5) (6) ALARM ON/OFF ALARM DWELL ALARM POLARITY VIDEO LOSS ALERT BEEPER ON EXIT key. The n Press the and keys to adjust the time. Options are: 1-60 SEC: automatic reset period. HOLD: alarm continues until the alarm camera key is pressed followed by the ALM ( ) key. FOLLOW: alarm continues until the alarm camera key is pressed followed by the ALM ( ) key. > > n Press the key to exit the menu. 5. 5. 1 Setup an Alarm Channel You can switch the alarm function ON/OFF for each of the four video input channels. n 5. 5. 3 Alarm Polarity The ALARM POLARITY function enables you to define how the alarm is generated for each alarm input, either normally open (NO) or normally closed (NC) contacts. n Select ALARM ON/OFF and press the following menu is displayed: ALARM ON/OFF (1) (2) (3) (4) (5) CHANNEL CHANNEL CHANNEL CHANNEL EXIT 1: 2: 3: 4: ON ON OFF ON key. The Select ALARM POLARITY and press the following menu is displayed: ALARM POLARITY (1) (2) (3) (4) (5) CHANNEL CHANNEL CHANNEL CHANNEL EXIT 1: 2: 3: 4: NO NO NO NO key. Press the and keys to move the cursor to required n Press the channel. [. . . ] 3 If an Alarm Dwell Time is set to HOLD mode, the alarm remains active until the alarm is reset. n Press the alarm camera key, then ALM ( ) key to cancel the alarm. 4 If an Alarm Dwell Time is set to FOLLOW mode, the alarm remains active until the alarm is reset. n Press the alarm camera key, then ALM ( ) key to cancel the alarm. [. . . ]