User manual PHILIPS LTC9383

[. . . ] Outdoor Camera Housings Eng F D E NL I LTC 9380 Series Philips Communication & Security Systems IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. [. . . ] The LTC 9383/60 and LTC 9388/60 housings can easily be used with either 115 volt or 24 volt cameras. The internal transformer provides 24 VAC for both the heater/defogger and 24 volt camera power. The transformer will provide flying leads for connection to the primary (white wire/pin 1, black wire/pin 6) and the secondary (white/black striped wires-pins 7 and 12). The housing is shipped with the heater/defogger connected to the secondary. Installing a 115 volt camera into the LTC 9383/60 or LTC 9388/60 housing requires the camera's line cord to be cut and connected with the transformer primary leads and the power supply line. Cut the power cord leaving enough cable to allow connection to the primary (approximately 5 inches). Strip no less than 6 mm (0. 25 in) and no more than 8 mm (0. 31 in) of insulation away from the wire, be sure not to nick the wires. Connect the supply line to the camera power cord and transformer primary leads. Use the wire nuts provided for this connection. The secondary flying leads (white/black striped) will not be used in this application and should be taped to prevent shorting. See wiring diagram Figure 11 for clarification and Figure 9 for power connection drawings. To Camera To Heater/Defogger Red Black White/Black Striped Figure 9: Liquid-Tight Fittings and Power Connector (Side & Top Views) 2. A screw/terminal lug is provided for securing a safety ground. To attach the safety grounding wire (green 115 volt, green/yellow 230 volt), first unscrew the terminal lug and strip and crimp the grounding wire into the lug. Next pull the grounding wire through the larger rear hole and attach the terminal lug to the cradle using the M4 x 10 screw provided. See Figure 10. Cradle 115 VAC Input 24 VAC No Connection White White/Black Striped Red To Camera To Heater/Defogger S925A10AE Large Rear Hole Safety Grounding Wire M4 Screw Terminal Lug S925A15AE Figure 11: LTC 9383/60/LTC 9388/60 Transformer Wired for 115 Volt Camera Installing a 24 volt camera into the LTC 9383/601 or LTC 9388/60 housing utilizes the internal transformer for camera power. Connect the supply (115 VAC) to the primary flying leads of the transformer (white wire/pin 1, black wire/pin 6). Use the wire nuts provided for this connection. Connect the secondary flying leads (white/black striped wires-pins 7 and 12) to the camera's 24 volt input. See wiring diagram Figure 12 for clarification and Figure 9 for power connection drawings. Figure 10: Securing Ground Wire 3. Pull any excess wire out of the cradle assembly and tighten the fitting to 8. 5 N-m to 9. 0 N-m (75 in-lb to 80 in-lb). This torque rating is approximately 1 to 1 1/2 turns past the point the fitting starts to grip the wire. 7 To Heater/Defogger Red Black White/Black Striped Connection of these housings to supply voltage in excess of 30 VAC source will cause damage. Do not remove the transformer insulator. [. . . ] Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9948A, TC1848B1, TC9970A Fixed, TC9948A, TC1848B1, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9948A, TC1848B1, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9938, TC9948A, TC1848B1, TC99581, TC9970A Fixed, TC9948A, TC1848B1, TC9970A Fixed , TC9948A, TC1848B1, TC9970A Fixed (manual iris only) 1. option denoted by a suffix "P". Also applies to models with pre-position 6. 2 LTC 9383/20 and LTC 9388/20 Housings The LTC 9383/20 and LTC 9388/20 Housings are UL Listed to Standard 2044. Only the following cameras can be used in these housings to maintain the UL Listing. These Housings require a 24 VAC, 60 Hz power supply. Camera Models LTC 0142/20 LTC 0143/20 LTC 0242/20 LTC 0243/20 LTC 0330/20 LTC 0350/20 LTC 0430/20 LTC 0450/20 TC352A, TC652BT TC362, TC382 TC372, TC392 TC552A, TC592 TC652B TC952, TC972 1. [. . . ]