User manual PHILIPS MC-105

[. . . ] Micro Hi-Fi System Audio MC-110 MC-105 MC-100 1 3140 115 28731 pg 001-022/MC1xx/22-Eng 1 10/5/01, 2:45 PM Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Italia DICHIARAZIONE DI CONFORMITA' Si dichiara che l'apparecchio MC-100, MC-105, MC-110 Philips risponde alle prescrizioni dell'art. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] Press PLAY·PAUSE 2; (on the remote control 2;) to start playback if in the STOP position. If you have selected SHUFFLE, playback starts automatically. To return to normal playback, press the respective SHUFFLE or REPEAT button until the various SHUFFLE/ REPEAT modes are no longer displayed. 4 5 3 Reviewing the programme In STOP mode, press and hold down PROGRAM for a while until the display shows all your stored track numbers in sequence. q You can also press STOP 9 to cancel your play mode. Erasing the programme You can erase the programme by: q pressing STOP 9 once in the STOP mode; q pressing STOP 9 twice during playback; q opening the CD compartment; PROGRAM disappears from the display. 13 3140 115 28731 pg 001-022/MC1xx/22-Eng 13 10/5/01, 2:46 PM English Radio Reception English STANDBY ON SELECT SOURCE Programming radio stations TUNER PROGRAM TIMER PROGRAM You can store up to a total of 40 radio stations in the memory. Automatic programming Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden. The system will only programme stations which are not in the memory already. TIMER ON·OFF DBB DSC INCREDIBLE SURR. INTERACTIVE SOUND VOLUME iR SENSOR STOP PRESET PLAY·PAUSE CLOCK RDS REPEAT BAND PREV TUNING NEXT SHUFFLE 1 Press PRESET 4 or 3 (on the remote control ¡ or TM ) to select the preset number where programming should start. Note: ­ If no preset number is selected, default is preset (1) and all your presets will be overridden. Tuning to radio stations 1 2 3 Select TUNER source. Press BAND once or more to select your waveband. Press down on TUNING à or á and release button. The radio automatically tunes to a station with sufficient reception. Display indication during automatic tuning: SEARCH. If a FM station is received in stereo, STEREO is shown. Repeat step 3 if necessary until you find the desired station. 2 Press PROGRAM for more than 2 seconds to activate programming. AUTO is displayed and available stations are programmed in order of waveband reception strength: FM followed by MW and LW. The last preset automatically stored will then be played. Manual programming 1 2 3 4 4 Tune to your desired station (see Tuning to radio stations). Press PRESET 4 or 3 (on the remote control ¡ or TM ) to allocate a number from 1 to 40 to this station. Press PROGRAM again to confirm the setting. PROGRAM disappears, the preset number and the frequency of the preset station are shown. Repeat the above four steps to store other stations. q To tune to a weak station, press TUNING à or á briefly and repeatedly until you have found optimal reception. 5 q You can override a preset station by storing another frequency in its place. 14 3140 115 28731 pg 001-022/MC1xx/22-Eng 14 10/5/01, 2:46 PM Radio Reception Tuning to preset radio stations q Press PRESET 4 or 3 (on the remote control ¡ or TM ) until the desired preset station is displayed. EON Enhanced Other Network allows you to search for an RDS station offering a certain programme type. If EON is available, is shown. RDS Radio Data System is a service that allows FM stations to show additional information. If you are receiving a RDS station, and the station name are displayed. [. . . ] 6. 0 / 2. 8 kg Standby power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . < 3 W Subject to modification pg 001-022/MC1xx/22-Eng 20 10/5/01, 2:46 PM Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. [. . . ]