User manual PHILIPS MC-122

[. . . ] Micro Hi-Fi System Audio MC-120 MC-122 MC-130 1 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Italia DICHIARAZIONE DI CONFORMITA' Si dichiara che l'apparecchio MC-120, MC-122, MC-130 Philips risponde alle prescrizioni dell'art. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] To start playback of your disc programme, press PLAY·PAUSE 2; (on the remote control 2;). 2 3 1 To select your play mode, press the SHUFFLE or REPEAT button before or during playback until the display shows the desired function. Press PLAY·PAUSE 2; (on the remote control 2;) to start playback if in the STOP position. If you have selected SHUFFLE, playback starts automatically. To return to normal playback, press the respective SHUFFLE or REPEAT button until the various SHUFFLE/ REPEAT modes are no longer displayed. 4 2 5 3 Reviewing the programme In STOP mode, press and hold down PROGRAM for a while until the display shows all your stored track numbers in sequence. G You can also press STOP 9 to cancel your play mode. Erasing the programme You can erase the programme by: G pressing STOP 9 once in the STOP mode; G pressing STOP 9 twice during playback; G opening the CD compartment; PROGRAM disappears from the display. 13 English Radio Reception English STANDBY-ON PROGRAM ON OFF Programming radio stations You can store up to a total of 40 radio stations in the memory. TIMER CLOCK RDS BAND REPEAT SHUFFLE PROGRAM SOURCE SELECT PLAY·PAUSE STOP Automatic programming Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden. The system will only programme stations which are not in the memory already. PREV NEXT iR 1 Press PRESET 3 or 4 (on the remote control ¡ or TM ) to select the preset number where programming should start. Note: ­ If no preset number is selected, default is preset (1) and all your presets will be overridden. Tuning to radio stations 1 2 3 Select TUNER source. Press BAND once or more to select your waveband. Press down on TUNING à or á and release button. The radio automatically tunes to a station with sufficient reception. Display indication during automatic tuning: SEARCH. If a FM station is received in stereo, STEREO is shown. Repeat step 3 if necessary until you find the desired station. 2 Press PROGRAM for more than 2 seconds to activate programming. AUTO is displayed and available stations are programmed in order of waveband reception strength: FM followed by MW and LW. The last preset automatically stored will then be played. Manual programming 1 2 3 4 Tune to your desired station (see Tuning to radio stations). Press PRESET 3 or 4 (on the remote control ¡ or TM ) to allocate a number from 1 to 40 to this station. Press PROGRAM again to confirm the setting. PROGRAM disappears, the preset number and the frequency of the preset station are shown. Repeat the above four steps to store other stations. G To tune to a weak station, press TUNING à or á briefly and repeatedly until you have found optimal reception. 4 5 G You can override a preset station by storing another frequency in its place. 14 Radio Reception Tuning to preset radio stations G Press PRESET 3 or 4 (on the remote control ¡ or TM ) until the desired preset station is displayed. Searching programme type (PTY) PTY helps you find a desired programme type. To enable PTY, first programme RDS stations into the tuner memory (see Programming radio stations) RDS Radio Data System is a service that allows FM stations to show additional information. If you are receiving a RDS station, and the station name are displayed. [. . . ] 5. 7 / 2. 7 kg Standby power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . < 3 W Subject to modification Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. [. . . ]