User manual PHILIPS MC150-21M

[. . . ] Micro Hi-Fi System MC150 México Es necesario que lea cuidadosamente su instructivo de manejo. PRECAUCIÓN - ADVERTENCIA No abrir, riesgo de choque eléctrico ATENCIÓN Verifique que el voltaje de alimentación sea el requerido para su aparato Para evitar el riesgo de choque eléctrico, no quite la tapa. En caso de requerir servicio, dirijase al personal calificado. Microsistema de Audio MC150/ 21 110­127 / 220­240V; ~50­60 Hz 25 W Philips Mexicana, S. A. San Fernando La Herradura Huixquilucan Localidad y Tel: Edo. 52784 Tel. 52 69 90 00 Exportador: Philips Electronics HK, Ltd. [. . . ] Use the ¡1 or 2TM (¡ or TM on remote control) to select your desired track number. Press PROGRAM (PROG on the remote control) to confirm the track number to be stored. Repeat steps 2-3 to select and store all desired tracks. FULLis displayed if you attempt to programme more than 20 tracks. To start playback of your disc programme, press 2;. Note: ­ If you wish, you can add further tracks to your current program. Make sure you are in the STOP position, and that you have not exceeded 20 tracks. 2 3 4 1 2 To select your play mode, press the SHUFFLE or REPEAT button before or during playback until the display shows the desired function. Press 2; to start playback if in the STOP position. If you have selected SHUFFLE, playback starts automatically. To return to normal playback, press the respective SHUFFLE or REPEAT button until the various SHUFFLE/ REPEAT modes are no longer displayed. 5 3 You can also press 9 to cancel your play mode. Reviewing the programme In STOP mode, press and hold down PROGRAM (PROG on the remote control) for a while until the display shows all your stored track numbers in sequence. Erasing the programme You can erase the programme by: pressing 9 once in the STOP mode; pressing 9 twice during playback; opening the CD compartment; PROG disappears from the display. 13 English Radio Reception English Programming radio stations You can store up to a total of 30 (20 FW and 10 MW) radio stations in the memory. Automatic programming Automatic programming will start with a chosen preset number 1. From this preset number upwards, former programmed radio stations will be overridden. 1 2 Tuning to radio stations 1 2 3 Select TUNER source. Press SOURCE (TUNER on the remote control) once or more to select your waveband. Press on TUNE à or á and release button. The radio automatically tunes to a station with sufficient reception. Display indication during automatic tuning Srch. Repeat step 3 if necessary until you find the desired station. Press SOURCE (TUNER on the remote control) once or more to select your waveband. Press ¡ or TM (on the remote control) to select the preset number where programming should start. Note: ­ If no preset number is selected, default is preset (1) and all your presets will be overridden. 3 Press PROGRAM (PROG on the remote control) for more than 2 seconds to activate programming. AUto is displayed and available stations are programmed in order of waveband reception strength. 4 Manual programming 1 2 3 Tune to your desired station (see Tuning to radio stations). Press PROGRAM (PROG on the remote control) to activate programming. Press ¡ or TM (on the remote control) to select a number from 1 to 20 for FM (or 1 to 10 for MW) to this station. Press PROGRAM (PROG on the remote control) again to confirm the setting. [. . . ] 4. 9 / 2. 3 kg Standby power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . < 3 W Subject to modification 19 English Troubleshooting English 20 WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. [. . . ]