User manual PHILIPS MC165C

[. . . ] If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. [. . . ] READ is displayed as the CD player scans the contents of a disc, and then the total number of tracks and playing time are shown. Press PLAY·PAUSE 2; (on the remote control 2;) to start playback. Current track number and elapsed playing time of the track are displayed during disc playback. 2 3 4 12 CD Operation Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. The play modes can also be combined with PROGRAMME. tracks of the entire disc/ programme are played in random order SHUFFLE and REPEAT ALL. . . to repeat the entire disc/ programme continuously in random order REPEAT ALL . . . repeats the entire disc/ programme REPEAT . . . . . . . . . . . . plays the current track continuously Programming track numbers Programme in the STOP position to select and store your disc tracks in the desired sequence. If you like, store any track more than once. Up to 20 tracks can be stored in the memory. 1 Press PROGRAM to enter the programming mode. A track number is shown and PROGRAM flashes. Use the PREV ¡1 or NEXT 2TM (on the remote control ¡ or TM) to select your desired track number. Press PROGRAM again to confirm the setting. PROGRAM disappears, the preset number and the frequency of the preset station are shown. Repeat the above four steps to store other stations. G To tune to a weak station, press TUNING à or á briefly and repeatedly until you have found optimal reception. 4 5 G You can override a preset station by storing another frequency in its place. 14 Radio Reception Tuning to preset radio stations G Press PRESET 3 or 4 (on the remote control ¡ or TM ) until the desired preset station is displayed. Searching programme type (PTY) PTY helps you find a desired programme type. To enable PTY, first programme RDS stations into the tuner memory (see Programming radio stations) RDS Radio Data System is a service that allows FM stations to show additional information. If you are receiving a RDS station, and the station name are displayed. When automatic programming is used, RDS stations will be programmed first. Scrolling through different RDS information G Press RDS briefly and repeatedly to scroll through the following information (if available): ­ Station name ­ Programme type such as NEWS, SPORT, POP M . . . ­ Radio text messages ­ Frequency Note: ­ If you press RDS and the RDS signal is not available NO RDS is displayed. 1 2 While receiving an RDS station, press RDS briefly until the programme type is displayed. Press PRESET 3 or 4 (on the remote control ¡ or TM ) until the desired programme type is displayed. Press and hold down on TUNING à or á (on the remote control à or á ) to start searching. The radio tunes to a RDS station broadcasting this programme type. [. . . ] 156 x 231 x 190 (mm) GENERAL INFORMATION AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ­ 230 V / 50 Hz Dimensions (w x h x d) . . . 140 x 231 x 280(mm) Weight (with/without speakers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]