User manual PHILIPS MCM238

[. . . ] Micro Hi-Fi System Register your product and get support at www. philips. com/welcome MCM238 MCM238 User manual Manuel d'utilisation Manual de usuario Benutzerhandbuch Gebruikershandleiding Manuale dell'utente Användarhandbok Brugervejledning Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Italia DICHIARAZIONE DI CONFORMITA' Si dichiara che l'apparecchio MCM238 Philips risponde alle prescrizioni dell'art. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 3 Amp, A. S. T. A. [. . . ] Notes for remote control: ­ First select the source you wish to control by pressing one of the source select keys on the remote control (for example CD, TUNER). ­ Then select the desired function (for example ÉÅ, í ë). , To replace the remote controls' battery (CR2025) Setting the clock After connecting MCM238 to the power supply, set the clock first. 1 Press and hold STANDBY-ON/ ECO POWER to switch the set to Standby mode. -- --:-- -- flashes by default if you have not set the clock. In the standby mode, press and hold CLOCK. SET CLOCK scrolls on the display 24 HR or 12 HR appears for the initial clock setting. To select 24-hour clock or 12-hour clock, a. Press CLOCK to confirm The hours digits start flashing Hold down or press VOLUME +/- repeatedly to set the hours. Press CLOCK to confirm The minutes digits start flashing Hold down or press VOLUME +/- repeatedly to set the minutes. Press CLOCK to confirm ­ To exit without storing the clock setting press STOP 9 Helpful hints: ­ The clock setting will be erased when the system is disconnected from the power supply. ­ The set will exit from the clock setting mode if no button is pressed within 90 seconds. ­ To set the clock automatically by using a time signal which is broadcast together with the RDS signal see chapter RDS: Setting the RDS clock. . 2 3 4 5 6 1 2 3 Push to open the battery tray. Replace a new battery according to the indicated polarity. Push the battery tray back to close it. CAUTION!­ Remove the battery if it is exhausted or will not be used for a long time. ­ Batteries contain chemical substances, so they should be disposed of properly. 15 English Basic Functions English Switching on/off the set and selecting functions 1 To switch on, press STANDBY-ON/ ECO POWER or SOURCE on the set (or y on the remote control) The set switches to the last source selected OR On the remote control, press the source button (e. g. When the set is on, press STANDBY-ON/ ECO POWER to switch off (or y on the remote control). To select your function, press SOURCE once or more on the set (or CD, TUNER, AUX on the remote control). Volume control Volume adjustment Adjust the volume by pressing VOLUME +/- . VOL and the actual value (between 1 and 31) are displayed. MUTE You can temporarily switch off the sound without switching off the set. To switch on the sound, you can: ­ press MUTE again; ­ adjust the volume controls; ­ change source. 2 3 1 2 Switching between Standby and ECO POWER mode 1 When the set is switched off, press and hold STANDBY-ON/ ECO POWER to switch between Standby and ECO POWER mode (or y on the remote control). [. . . ] <1 W Specifications and external appearance are subject to change without notice. Maintenance Cleaning the Cabinet Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives. Cleaning Discs When a disc becomes dirty, clean it with a cleaning cloth. Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for analogue records. [. . . ]