User manual PHILIPS MCM25037

[. . . ] If the mains plug contains a fuse, this should have a value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 3 Amp. Note: The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). ¶ As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows: ­ Connect the blue wire to the terminal marked N or coloured black. [. . . ] To switch on the sound, you can: ­ press MUTE again; ­ adjust the volume controls; ­ change source. 2 3 1 2 Switching between Standby and ECO POWER mode 1 When the set is switched off, press and hold STANDBY-ON/ ECO POWER to switch between Standby and ECO POWER mode (or y on the remote control). In ECO POWER mode (power-saving mode): ECO PWR scrolls on the display. In Standby mode: The clock is displayed. Helpful hints: ­ In the standby/Eco power mode, the tone, sound settings, tuner presets and the volume level (up to a maximum volume level of 12) will be retained in the set's memory. Sound control DSC Digital Sound Control enables you to select predefined sound settings. Press DSC repeatedly to select the desired sound setting: ROCK, JAZZ, POP, CLASSIC, OPTIMAL. DBB Press DBB (Dynamic Bass Boost) once or more to switch bass enhancement on or off. DBB appears if DBB is activated Displaying the clock During playback, press DISPLAY/CLOCK on the remote control repeatedly to switch between the clock display and the playback display. Notes: ­ When playing MP3 files, you will get track information (ID3 tag) by pressing DISPLAY/ CLOCK. Auto-standby In Disc or USB mode, when the set reaches the end of the playback and remains in the stop position for more than 15 minutes, the set will auto switch to stand by to save power. In standby mode, the set will will auto switch to Eco power standby after 15 minutes of in-activation. When iPod is plugged in and charged in standby mode, the set will not switch to Eco power mode. 16 CD Discs for playback With this system, you can play ­ all pre-recorded audio CDs (CDDA) ­ all finalized audio CD-Rs and CD-RWs ­ MP3/WMA-CDs (CD-Rs/CD-RWs with MP3/WMA files) IMPORTANT!­ Make sure that the file names of MP3 files end with . mp3. MP3/WMA: press ALBUM/ PRESET and 4 / ¢ to select the desired album and track. 3 Press PROGRAM to confirm. Display shows briefly the number of tracks programmed. Then, the display shows the track number you just stored. Repeat steps 2-3 to select and store all desired tracks. FULL is displayed if you attempt to program more than 20 tracks. Helpful hints: ­ The set will return to the stop position if no button is pressed within 90 seconds. ­ MP3/WMA: When playing a program, use of ALBUM/ PRESET are void. 4 1 2 During playback, press and hold 4 / ¢ The CD plays at a high speed. When you recognize the passage you want, release 4 or ¢. Normal playback resumes. 5 Erasing the program You can erase the contents of the memory by: Press STOP 9 ­ once if in the stop position; ­ twice during playback; Press STANDBY-ON/ ECO POWER. PROG disappears. 18 CD Different play modes: REPEAT, SHUFFLE REP TRACK­ plays the current track continuously. REP ALL­ plays the entire disc/program continuously. [. . . ] Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for analogue records. Cleaning the disc lens After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner. 27 English Troubleshooting English 28 WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. [. . . ]