User manual PHILIPS MCM277

[. . . ] Micro Hi-Fi System Register your product and get support at MCM277 www. philips. com/welcome User manual Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 3 Amp, A. S. T. A. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. [. . . ] The machine does not contain any userserviceable parts. Modification of the product could result in hazardous radiation of EMC or other unsafe operation. 11 English Preparation English Using the remote control IMPORTANT!­ Remove the protective plastic tab before using the remote control. ­ Always point the remote control directly towards IR area. Setting the clock After connecting MCM277 to the power supply, set the clock first. 1 Press and hold STANDBY-ON/ ECO POWER to switch the set to Standby mode The display shows the set time -- --:-- -- flashes by default if you have not set the clock 2 In the standby mode, press and hold DISPLAY/ CLOCK on the remote control SET CLOCK scrolls on the display 24 HR or 12 HR appears for the initial clock setting. To select 24-hour clock or 12-hour clock, On the remote control, press VOL +/once or more (or turn VOLUME on the set) On the remote control, press DISPLAY/ CLOCK to confirm The hours digits start flashing 3 Hold down or press VOL +/- repeatedly to set the hours (or turn VOLUME on the set) Remove the plastic protective sheet Notes for remote control: ­ First select the source you wish to control by pressing one of the source select keys on the remote control (for example CD, TUNER). ­ Then select the desired function (for example ÉÅ, 4 , ¢). To replace the remote controls' battery 4 5 6 1 2 3 4 Press and hold 1 as indicated. Simultaneously, pull the battery tray at 4. Remove the old battery and put a new CR2025 battery in place. Put back the battery tray. Press DISPLAY/CLOCK to confirm The minutes digits start flashing Hold down or press VOL +/- repeatedly to set the minutes (or turn VOLUME on the set) Press DISPLAY/CLOCK to confirm ­ To exit without storing the clock setting press STOP 9 Helpful hints: ­ The clock setting will be erased when the system is disconnected from the power supply. ­ The set will exit from the clock setting mode if no button is pressed within 90 seconds. ­ To set the clock automatically by using a time signal which is broadcast together with the RDS signal see chapter RDS: Automatic clock setting via RDS. 1 2 CR2025 3 CAUTION!­ Remove the battery if it is exhausted or will not be used for a long time. ­ Batteries contain chemical substances, so they should be disposed of properly. ­ Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 12 Basic Functions Switching on/off the set and selecting functions 1 To switch on, press STANDBY-ON/ ECO POWER or SOURCE on the set (or y on the remote control) The set switches to the last source selected OR On the remote control, press the source button (e. g. USB, CD, TUNER, AUX) When the set is on, press STANDBY-ON/ ECO POWER to switch off (or y on the remote control) To select your function, press SOURCE once or more on the set (or USB, CD, TUNER, AUX on the remote control) Helpful hints: ­ You can also switch on the set by pressing CD OPEN · CLOSEç Helpful hints: ­ In the standby/Eco power mode, the tone, sound settings, tuner presets and the volume level (up to a maximum volume level of 20) will be retained in the set's memory. Auto-standby When the set has reached the end of CD playback and remains in the stop position for more than 15 minutes, the set will switch off automatically to save power. 2 3 Volume control Volume adjustment Adjust the volume by using the VOLUME rotary on the set or by pressing VOL +/- on the remote control VOL and the actual value (between 1 and 31) are displayed VOL MIN is the minimum volume level VOL MAX is the maximum volume level MUTE You can temporarily switch off the sound without switching off the set. Press MUTE on the remote control to switch off the sound MUTE appears. Playback continues without sound To switch on the sound, you can: ­ press MUTE again; ­ adjust the volume controls; ­ change source Switching between Standby and ECO POWER mode 1 When the set is switched off, press and hold STANDBY-ON/ ECO POWER to switch between Standby and ECO POWER mode (or y on the remote control) In ECO POWER mode (power-saving mode): ECO PWR scrolls on the display The display is switched off The Red indicator lights up In Standby mode: The clock is displayed 1 2 13 English Basic Functions English 14 Sound control DSC Digital Sound Control enables you to select predefined sound settings. Press DSC repeatedly to select the desired sound setting: ROCK, JAZZ, POP, CLASSIC DBB Press DBB (Dynamic Bass Boost) once or more to switch bass enhancement on or off. [. . . ] If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. Problem "NO DISC" is displayed. Wait until the moisture condensation at the lens has cleared. Replace or clean the disc, see "Maintenance". Use a finalised CD-RW or a correct MP3/WMA -CD format disc. [. . . ]