User manual PHILIPS MCM390

[. . . ] Micro Hi-Fi System MCM390 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Italia DICHIARAZIONE DI CONFORMITA' Si dichiara che l'apparecchio MCM390 Philips risponde alle prescrizioni dell'art. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] Insert a disc with the printed side facing up and press OPEN·CLOSE3 to close the CD door. "READING" is displayed as the CD player scans the contents of a disc, and then the total number of tracks and album are shown. Å Selecting a different track Press S or T (¡ or TM) repeatedly until the desired track number appears in the display. If playback is stopped, pressÉ to start Å playback. 4 12 CD/MP3-CD Operations Finding a passage within a track 1 2 Press and hold down on S or T ( à or á on the remote control). When you recognize the passage you want, release S or T ( à or áon the remote control). Normal playback continues. Programming the disc tracks Programming tracks is possible when playback is stopped. Up to 20 tracks can be stored in the memory in any order. 1 2 Press PROGRAM to enter the programming mode. A track number is shown and PROG flashes. Press S or T (¡ or TM) repeatedly to select your desired track number. Selecting a desired album/track (MP3 disc only) To select a desired album Press 4 or 3 repeatedly. To select a desired track Press S or T (¡ or TM) repeatedly. For MP3 disc, press 4 / 3 and S / T (¡ or TM) to select the desired album and track for programming. 3 4 5 Press PROGRAM to confirm the track number to be stored. Repeat steps 2-3 to select and store all desired tracks. To start playback of your disc programme, press Ç followed byÉÅ. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. 1 Press MODE on the remote control to select : SHUFFLE ­ tracks of the entire disc/ programme are played in random order. SHUFFLE REPEAT ALL ­ to repeat the entire disc/ programme continuously in random order. REPEAT ALL ­ to repeat the entire disc/ programme. REPEAT ­ to repeat the current track. To return to normal playback, press MODE until the various SHUFFLE/ REPEAT modes are no longer displayed. If you attempt to programme more than 20 tracks, "FULL" will appear on the display. In this case : The system will exit programming mode automatically. Pressing Ç button will erase all the programmed tracks. Pressing ÉÅ button will start playback the programmed tracks. Note: ­ It is not possible to create a programme with MP3 tracks from multiple CDs. 2 Reviewing the programme In stop mode, press and hold PROGRAM until the display shows all your stored track numbers in sequence. You can also press 9 to cancel your play mode. Note: ­ If Shuffle is activated on a MP3-CD, all titles stored in the disc will be played in random order. Erasing the programme Press Ç once when playback is stopped or twice during playback. PROG disappears and "CLEAR" is displayed. 13 English Radio Reception English Programming radio stations You can store up to a total of 40 radio stations in the memory. [. . . ] Use a cotton swab slightly moistened with cleaning fluid or alcohol. You can also clean the heads by playing a cleaning tape once. A ABC Demagnetizing the heads Use a demagnetizing tape available at your dealer. Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. [. . . ]