User manual PHILIPS MCM530/21T

[. . . ] Micro Hi-Fi System MC M530 visit our website www. audio. philips. com to download latest UPDATES of USB PC Link Driver MusicMatch Jukebox softwares and FAQs. Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Italia DICHIARAZIONE DI CONFORMITA' Si dichiara che l'apparecchio MC M530, Philips risponde alle prescrizioni dell'art. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] Press CLOCK (or CLOCK·TIMER) to store the setting. Notes: ­ The clock setting will be erased when the system is disconnected from the power supply. ­ The system will exit clock setting mode if no button is pressed within 90 seconds. ­ To set the clock automatically through the time information in the RDS signal, refer to "Tuner Operations ­ Setting the RDS clock". Demonstration mode If the demonstration mode is active, whenever you switch the system to the Eco Power standby or standby mode, it will begin showing the various features offered by the system. To activate the demonstration In Eco Power standby/standby mode, press and hold Ç on the main unit for 5 seconds until "DEMO ON" is displayed. To deactivate the demonstration Press and hold Ç on the main unit for 5 seconds until "DEMO OFF" is displayed. 15 English Basic Operations English 16 Selecting different display modes Dim mode You can select the desired brightness for the display panel. In any active mode, press DIM repeatedly to select DIM 1, DIM 2, DIM 3 or DIM OFF display mode. DIM is shown, except for DIM OFF mode. DIM mode DIM OFF DIM 1 DIM 2 DIM 3 Button illumination on on on off Display brightness full full half half Spectrum analyser on off on off Sound control You are only able to select one of the sound controls at a time : MAX sound, DSC or VEC. MAX sound MAX sound provides the best mixture of various sound features (DSC, VEC for example). Press MAX SOUND (or MAX ON /OFF on remote). If activated, MAX is shown and the MAX SOUND button lights up. All other sound effects (DSC or VEC) will be switched off automatically If MAX SOUND is activated together with Philips Sound Agent 2, the PRESET and REVERB sound effect will be switched automatically to Neutral and No Environment modes respectively. Digital Sound Control DSC provides a different type of preset sound equaliser setting. Press DSC repeatedly to select: OPTIMAL, JAZZ, ROCK or POP. Virtual Environment Control VEC provides a different type of environmentbased equaliser setting. Press VEC repeatedly to select: HALL, CINEMA, CONCERT or CYBER. Note: ­ Pressing DIM button in standby mode will toggle between half and full brightness. Clock display mode You can choose to show the clock display only. Press CLOCK· TIMER (or CLOCK on remote control). In any active mode, pressing the button again will resume normal display. Note: ­ If you pressed any buttons in the clock display mode, the display will briefly show the information related to the selected mode. Volume control Adjust MASTER VOLUME (or press VOL +/- on remote) to increase or decrease the sound level. "VOL MUTE" is the minimum volume level and "0 dB" is the maximum volume level. To switch off the volume temporarily Press MUTE on the remote. [. . . ] Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. Problem Auto Installation of the Installer CD-ROM did not install the Philips Sound Agent 2 onto my PC. When in USB PC LINK mode, "NO CONNECTION" is displayed. Solution Check that your PC's Operating System is running on Windows 2000/XP. I want the minimum effect from the Philips Sound Agent 2 sound mode when listening to MP3 music streaming via USB PC Link. [. . . ]