User manual PHILIPS MCM726

[. . . ] Micro Hi-Fi System MCM726 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Italia DICHIARAZIONE DI CONFORMITA' Si dichiara che l'apparecchio MCM726 Philips risponde alle prescrizioni dell'art. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 2 5616 JB Eindhoven, The Netherlands 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] Up to 20 tracks can be stored in the memory in any order. 1 2 Press PROGRAM to enter the programming mode. A track number is shown and PROG flashes. Press TUNING S/T (S/T on the remote control) repeatedly to select your desired track number. Selecting a desired album/track To select a desired album (MP3 disc only) Press ALBUM/PRESET 4/3 repeatedly. To select a desired track Press TUNING S/T (S/T on the remote control) repeatedly. For MP3 disc, press ALBUM/PRESET 4/3 and TUNING S/T (S/T on the remote control) to select the desired album and track for programming. 3 4 5 Press PROGRAM to confirm the track number to be stored. Repeat steps 2-3 to select and store all desired tracks. To start playback of your disc programme, press Ç followed byÉÅ. PROG -- -- OK is displayed briefly. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. . 1 Press REPEAT and SHUFFLE on the remote control to select : SHUF ­ tracks of the entire disc/ programme are played in random order. SHUF REP ALL ­ to repeat the entire disc/ programme continuously in random order. REP ALL ­ to repeat the entire disc/ programme. To return to normal playback, press REPEAT and SHUFFLE until the various SHUFFLE/ REPEAT modes are no longer displayed. If you attempt to programme more than 20 tracks, "FULL" will appear on the display. In this case : The system will exit programming mode automatically. Pressing Ç button will erase all the programmed tracks. Pressing ÉÅ button will start playback of the programmed tracks. 2 Reviewing the programme In stop mode, press and hold PROGRAM until the display shows all your stored track numbers in sequence. You can also press 9 to cancel your play mode. Note: If Shuffle is activated on a MP3-CD, all titles stored in the disc will be played in random order. Erasing the programme Press Ç once when playback is stopped or twice during playback. PROG disappears and "CLEAR" is displayed. 15 English Radio Reception English Programming radio stations You can store up to 40 radio stations in the memory. Automatic programming Automatic programming will star t with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden. 1 Press ALBUM/PRESET 4/3 to select the preset number where programming should start. Note: ­ If no preset number is selected, default is preset (1) and all your presets will be overridden. Tuning to radio stations 1 2 3 Select TUNER source. "TUNER" is displayed briefly. Press BAND/DISPLAY (or TUNER on the remote control) to select the desired waveband : FM, MW or LW. Press down on TUNING S/T (S/T on the remote control) and release the button. The display will show "SEARCH" until a radio station with sufficient signal strength is found. [. . . ] You can also clean the heads by playing a cleaning tape once. A ABC Demagnetizing the heads Use a demagnetizing tape available at your dealer. Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. [. . . ]